ZMNHWD Qubino Flush RGBW Dimmer

This describes the Z-Wave device ZMNHWD, manufactured by Goap with the thing type UID of qubino_zmnhwd_00_000.

Qubino Flush RGBW Dimmer

Overview

Qubino Flush RGBW module controls RGB/RGBW strips and LED strips or bulbs and has 5 special scene effects. It can also control halogen lights and fans. Its extremely small size allows for easy installation behind wall sockets and switches. Controlled devices may be powered by 12 or 24 VDC.

Supported control types:

  • Push button (monostable switch)
  • Bistable switch

This should hopefully work with models ZMNHWD1-ZMNHWD8 (which work on different frequencies).

Inclusion Information

To include the device, press the service button 3 times within 2 seconds. The LED will turn green if the device was properly included.

The device supports auto inclusion: Install the device and connect the power. The auto inclusion function will be active for about 2 minutes.

Exclusion Information

To exclude the device, press the service button 3 times within 2 seconds. The green LED will blink if the device was properly included and the device will be reset to factory defaults.

Channels

The following table summarises the channels available for the ZMNHWD Qubino Flush RGBW Dimmer.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer
Color Control color_color color_color   Color
Color Temperature color_temperature color_temperature ColorLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the ZMNHWD Qubino Flush RGBW Dimmer. Detailed information on each parameter can be found below.

Parameter Description
1: Input switch type Change the type of switch (bistable/monostable)
2: Switch mode Choose RGBW Dimmer operation mode.
3: Auto scene mode set Activation of the programmed scene changing color shades.
4: Auto scene duration Change auto scene mode duration.
1: Send basic report to this group  

1: Input switch type

Change the type of switch (bistable/monostable)

Overview

NOTE: Please power cycle the device when parameter is changed.

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 1
Options bistable switch type (1)      
  monostable (push button) switch type (2)      

2: Switch mode

Choose RGBW Dimmer operation mode.

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 1
Options Normal Mode (1)      
  Brightness Mode (2)      
  Rainbow Mode (3)      

3: Auto scene mode set

Activation of the programmed scene changing color shades.

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options Ocean (1)      
  Lightning (2)      
  Rainbow (3)      
  Snow (4)      
  Sun (5)      

4: Auto scene duration

Change auto scene mode duration.

Overview
  • 1 - 127 delay duration is from 1s to 127s
  • -128 ~ -1 delay duration is from 1min. to 127min.
Property Value
Configuration ID config_4_1
Data Type INTEGER
Range -128 to 127
Default Value 3

1: Send basic report to this group

Overview

The Module can be set 1 auto-report ID in Group 1.

The Module will send BASIC_REPORT to device associated in Group 1 when correspond Device is activated.

Property Value
Configuration ID group_1
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.