The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

BE468 Touchscreen Deadbolt

This describes the Z-Wave device BE468, manufactured by Allegion with the thing type UID of schlage_be468_00_000.

The device is in the category of Lock, defining Devices whose primary pupose is locking something.

BE468 product image

The BE468 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

Overview

Z-Wave Enabled residential auto-throw deadbolt

Inclusion Information

Extend the bolt on the lock and then perform the following:

Enter 6 Digit Programming Code, then press 0. There will be a green check mark if enrolled or a red X if not enrolled

To verify enrollment:

1. Remove the battery cover. See Replacing the Batteries on page 4 of the User Guide.

2. Disconnect the battery connector.

3. While watching the inside Schlage button, reconnect the battery connector.

4. The inside Schlage button will blink if the lock is enrolled.

Exclusion Information

Same as inclusion

Wakeup Information

N/A

Channels

The following table summarises the channels available for the BE468 -:

Channel Channel Id Category Item Type
Door Lock lock_door Door Switch
Alarm (raw) alarm_raw   String
Battery Level battery-level Battery Number

Door Lock

Lock and unlock the door.

The lock_door channel supports the Switch item and is in the Door category.

Alarm (raw)

Provides the raw alarm status information as a string, including alarm type and level, in the following json format:

{“notification”:”ACCESS__MANUAL_LOCK”, “type”:”ACCESS_CONTROL”,”event”:”1”,”status”:”255”}

{“notification”:”ACCESS__MANUAL_UNLOCK”, “type”:”ACCESS_CONTROL”,”event”:”2”,”status”:”255”}

{“notification”:”ACCESS__KEYPAD_LOCK”, “code”:”1”, “type”:”ACCESS_CONTROL”,”event”:”5”,”status”:”255”}

{“notification”:”ACCESS__KEYPAD_UNLOCK”,”code”:”1”, “type”:”ACCESS_CONTROL”,”event”:”6”,”status”:”255”}

{“notification”:”ACCESS__LOCK_JAMMED”, “type”:”ACCESS_CONTROL”,”event”:”11”,”status”:”255”}

{“notification”:”ACCESS__KEYPAD_LOCK”, “type”:”ACCESS_CONTROL”,”event”:”5”,”status”:”255”}

{“notification”:”ACCESS_CONTROL__KEYPAD_TEMPORARILY_DISABLED”, “type”:”ACCESS_CONTROL”,”event”:”16”,”status”:”255”}

{“notification”:”BURGLAR__TAMPER_UNKNOWN”, “type”:”BURGLAR”,”event”:”2”,”status”:”255”}

{“notification”:”HOME_SECURITY__INTRUSION_UNKNOWN”, “type”:”BURGLAR”,”event”:”2”,”status”:”255”}

{“notification”:”POWER__REPLACE_BATTERY_SOON”, “type”:”POWER_MANAGEMENT”,”event”:”10”,”status”:”255”}

{“notification”:”POWER_MANAGEMENT__REPLACE_BATTERY_SOON”, “type”:”POWER_MANAGEMENT”,”event”:”10”,”status”:”255”}

Provides alarm parameters as json string.

The alarm_raw channel supports the String item. This is a read only channel so will only be updated following state changes from the device.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 5 configuration parameters available in the BE468. Detailed information on each parameter can be found in the sections below.

Param Name Description
3 Beeper Audio feedback when keypad pressed during normal operation
4 Vacation Mode Prevents all user codes from unlocking the deadbolt
5 Lock & Leave Press the Schlage button to lock the deadbolt
15 Auto Lock Automatically locks 30 seconds after unlocking
16 User Code PIN Length User codes can be 4-8 digits. Changing length will delete all existing codes.
  Lock Timeout Sets the time after which the door will auto lock

Parameter 3: Beeper

Audio feedback when keypad pressed during normal operation

The following option values may be configured -:

Value Description
0 Disable
255 Enable

The manufacturer defined default value is 255 (Enable).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Vacation Mode

Prevents all user codes from unlocking the deadbolt

The following option values may be configured -:

Value Description
0 Disable
255 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Lock & Leave

Press the Schlage button to lock the deadbolt

The following option values may be configured -:

Value Description
0 Disable
255 Enable

The manufacturer defined default value is 255 (Enable).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 15: Auto Lock

Automatically locks 30 seconds after unlocking

The following option values may be configured -:

Value Description
0 Disable
255 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 16: User Code PIN Length

User codes can be 4-8 digits. Changing length will delete all existing codes.

Values in the range 4 to 8 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_16_1 and is of type INTEGER.

Lock Timeout

Sets the time after which the door will auto lock.

This parameter has the configuration ID doorlock_timeout and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The BE468 supports 1 association group.

Group 1: Group 1

This group supports 2 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_APPLICATION_STATUS_V1  
COMMAND_CLASS_DOOR_LOCK_V1  
COMMAND_CLASS_USER_CODE_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V3  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_SECURITY_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.