The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

BE469 Touchscreen Deadbolt

This describes the Z-Wave device BE469, manufactured by Allegion with the thing type UID of schlage_be469_00_000.

The device is in the category of Lock, defining Devices whose primary pupose is locking something.

BE469 product image

The BE469 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

Overview

Touchscreen Deadbolt with Alarm

Inclusion Information

Extend the bolt on the lock and then perform the following:

Enter 6 Digit Programming Code, then press 0. There will be a green check mark if enrolled or a red X if not enrolled

To verify enrollment:
1. Remove the battery cover. See Replacing the Batteries on page 4 of the User Guide.
2. Disconnect the battery connector.
3. While watching the inside Schlage button, reconnect the battery connector.
4. The inside Schlage button will blink if the lock is enrolled.

Exclusion Information

Same as inclusion

Wakeup Information

N/A

Channels

The following table summarises the channels available for the BE469 -:

Channel Channel Id Category Item Type
Door Lock lock_door Door Switch
Alarm (raw) alarm_raw   String
Battery Level battery-level Battery Number

Door Lock

Lock and unlock the door.

The lock_door channel supports the Switch item and is in the Door category.

Alarm (raw)

Provides the raw alarm status information as a string, including alarm type and level, in the following json format:

{“notification”:”ACCESS__MANUAL_LOCK”, “type”:”ACCESS_CONTROL”,”event”:”1”,”status”:”255”} {“notification”:”ACCESS__MANUAL_UNLOCK”, “type”:”ACCESS_CONTROL”,”event”:”2”,”status”:”255”} {“notification”:”ACCESS__KEYPAD_LOCK”, “code”:”1”, “type”:”ACCESS_CONTROL”,”event”:”5”,”status”:”255”} {“notification”:”ACCESS__KEYPAD_UNLOCK”,”code”:”1”, “type”:”ACCESS_CONTROL”,”event”:”6”,”status”:”255”} {“notification”:”ACCESS__LOCK_JAMMED”, “type”:”ACCESS_CONTROL”,”event”:”11”,”status”:”255”} {“notification”:”ACCESS__KEYPAD_LOCK”, “type”:”ACCESS_CONTROL”,”event”:”5”,”status”:”255”} {“notification”:”ACCESS_CONTROL__KEYPAD_TEMPORARILY_DISABLED”, “type”:”ACCESS_CONTROL”,”event”:”16”,”status”:”255”} {“notification”:”BURGLAR__TAMPER_UNKNOWN”, “type”:”BURGLAR”,”event”:”2”,”status”:”255”} {“notification”:”HOME_SECURITY__INTRUSION_UNKNOWN”, “type”:”BURGLAR”,”event”:”2”,”status”:”255”} {“notification”:”POWER__REPLACE_BATTERY_SOON”, “type”:”POWER_MANAGEMENT”,”event”:”10”,”status”:”255”} {“notification”:”POWER_MANAGEMENT__REPLACE_BATTERY_SOON”, “type”:”POWER_MANAGEMENT”,”event”:”10”,”status”:”255”}

Provides alarm parameters as json string.

The alarm_raw channel supports the String item. This is a read only channel so will only be updated following state changes from the device.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 15 configuration parameters available in the BE469. Detailed information on each parameter can be found in the sections below.

Param Name Description
3 Beeper  
4 Vacation Mode  
5 Lock & Leave  
6 User Slot Status User slot status
7 Lock Specific Alarm Mode BE469 Only
8 Lock Specific Alarm Alert Sensitivity  
9 Lock Specific Alarm Tamper Sensitivity  
10 Lock Specific Alarm Kick Sensitivity BE469 Only
11 Lock Specific Alarm Disable—Local Controls  
12 Electronic Transition Count  
13 Mechanical Transition Count  
14 Electronic Failed Count  
15 Auto Lock  
16 User Code PIN Length User Code PIN length, a value between 4 and 8 (default 4)
18 Get Bootloader Version  
  Lock Timeout Sets the time after which the door will auto lock

Parameter 3: Beeper

The following option values may be configured -:

Value Description
0 Disable Beeper
255 Enable Beeper

The manufacturer defined default value is 255 (Enable Beeper).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Vacation Mode

The following option values may be configured -:

Value Description
0 Disable Vacation Mode
255 Enable Vacation Mode

The manufacturer defined default value is 0 (Disable Vacation Mode).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Lock & Leave

The following option values may be configured -:

Value Description
0 Disable Lock & Leave
255 Enable Lock & Leave

The manufacturer defined default value is 0 (Disable Lock & Leave).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: User Slot Status

User slot status Byte 1 (msb): Bit 7: User 8 Status Bit 6: User 7 Status Bit 5: User 6 Status Bit 4: User 5 Status Bit 3: User 4 Status Bit 2: User 3 Status Bit 1: User 2 Status Bit 0: User 1 Status Byte 2 : Bit 7: User 16 Status Bit 6: User 15 Status Bit 5: User 14 Status Bit 4: User 13 Status Bit 3: User 12 Status Bit 2: User 11 Status Bit 1: User 10 Status Bit 0: User 9 Status Byte 3 : Bit 7: User 24 Status Bit 6: User 23 Status Bit 5: User 22 Status Bit 4: User 21 Status Bit 3: User 20 Status Bit 2: User 19 Status Bit 1: User 18 Status Bit 0: User 17 Status Byte 4 (lsb): Bit 7: reserved Bit 6: reserved Bit 5: User 30 Status Bit 4: User 29 Status Bit 3: User 28 Status Bit 2: User 27 Status Bit 1: User 26 Status Bit 0: User 25 Status Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_6_4 and is of type INTEGER. This is a read only parameter.

Parameter 7: Lock Specific Alarm Mode

BE469 Only

The following option values may be configured -:

Value Description
0 Alarm Off
1 Alert
2 Tamper
3 Forced Entry

The manufacturer defined default value is 0 (Alarm Off).

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: Lock Specific Alarm Alert Sensitivity

The following option values may be configured -:

Value Description
0 Not Supported
1 Most Sensitive
2 More Sensitive
3 Medium Sensitivity
4 Less Sensitive
5 Least Sensitive

The manufacturer defined default value is 0 (Not Supported).

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Lock Specific Alarm Tamper Sensitivity

The following option values may be configured -:

Value Description
0 Not Supported
1 Most Sensitive
2 More Sensitive
3 Medium Sensitivity
4 Less Sensitive
5 Least Sensitive

The manufacturer defined default value is 0 (Not Supported).

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Parameter 10: Lock Specific Alarm Kick Sensitivity

BE469 Only

The following option values may be configured -:

Value Description
0 Not Supported
1 Most Sensitive
2 More Sensitive
3 Medium Sensitivity
4 Less Sensitive
5 Least Sensitive

The manufacturer defined default value is 0 (Not Supported).

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: Lock Specific Alarm Disable—Local Controls

The following option values may be configured -:

Value Description
0 Disable Local Control
255 Enable Local Control

The manufacturer defined default value is 0 (Disable Local Control).

This parameter has the configuration ID config_11_1 and is of type INTEGER.

Parameter 12: Electronic Transition Count

This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 2147483647 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_12_4 and is of type INTEGER. This is a read only parameter.

Parameter 13: Mechanical Transition Count

This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 2147483647 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_13_4 and is of type INTEGER. This is a read only parameter.

Parameter 14: Electronic Failed Count

This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 2147483647 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_14_4 and is of type INTEGER. This is a read only parameter.

Parameter 15: Auto Lock

The following option values may be configured -:

Value Description
0 Disable Auto Lock
255 Enable Auto Lock

The manufacturer defined default value is 0 (Disable Auto Lock).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 16: User Code PIN Length

User Code PIN length, a value between 4 and 8 (default 4)

The following option values may be configured -:

Value Description
4 Four Digits
5 Five Digits
6 Six Digits
7 Seven Digits
8 Eight Digits

The manufacturer defined default value is 4 (Four Digits).

This parameter has the configuration ID config_16_1 and is of type INTEGER.

Parameter 18: Get Bootloader Version

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_18_1 and is of type INTEGER. This is a read only parameter.

Lock Timeout

Sets the time after which the door will auto lock.

This parameter has the configuration ID doorlock_timeout and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The BE469 supports 1 association group.

Group 1: Alarm Reports

This group supports 2 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_APPLICATION_STATUS_V1  
COMMAND_CLASS_DOOR_LOCK_V1  
COMMAND_CLASS_USER_CODE_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V3  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V0  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_SECURITY_V0  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.