L 810 LED iHF Sensor-switched outdoor up and downlighting

This describes the Z-Wave device L 810 LED iHF, manufactured by Steinel with the thing type UID of steinel_l810ledihf_00_000.

Sensor-switched outdoor up and downlighting

Channels

The following table summarises the channels available for the L 810 LED iHF Sensor-switched outdoor up and downlighting.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer
Scene Number scene_number scene_number   Number
Binary Sensor sensor_binary sensor_binary Door Switch
Sensor (luminance) sensor_luminance sensor_luminance Temperature Number
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Alarm (system) alarm_system alarm_system   Switch
Dimmer 1 switch_dimmer1 switch_dimmer DimmableLight Dimmer
Scene Number 1 scene_number1 scene_number   Number
Alarm (burglar) 2 alarm_burglar2 alarm_burglar Door Switch

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Dimmer 1

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the L 810 LED iHF Sensor-switched outdoor up and downlighting. Detailed information on each parameter can be found below.

Parameter Description
0: Brighntes Meas Interval Brightness measuring interval [min]: (only SLAMP)
1: Time Duration of light after motion detection.
2: Light Light threshold [lx]:
3: Dim Night dim mode and time [min]: (only for SLAMP with DIM ability)
4: Range Motion Radar Range [cm]: (only for iHF sensor)
5: Sensity Motion Radar Sensitivity [%]: (SLAMP+SPIR)
8: Global_Light Use external Ambient Light value:
9: Slave_Mode Disable local control:
10: Off_Behaviour Off behaviour (timeout):
11: On_Behaviour On behaviour (timeout):
12: On_Time_Over On behaviour time over (timeout):
13: On_Off_Behaviour Sequence On-Off behaviour (timeout):
14: Off_On_Behaviour Sequence Off-On behaviour (timeout):
15: Sequence_Time Sequence timing:
16: Motion_Disable Motion Off behaviour (timeout):
1: General: Lifeline Lifeline
2: Control: Key01 On/Off control
3: Notification: Motion Motion Begin/End (PIR/radar/iHF)
4: Sensor: Luminescence Ambient light
5: Control: Key02 On/Off button

0: Brighntes Meas Interval

Brightness measuring interval [min]: (only SLAMP)

Overview

Interval for measuring ambient light when lamp is on (lamp switches off briefly and measures). 0 = function is off.

Property Value
Configuration ID config_0_1
Data Type INTEGER
Range 0 to 120
Default Value 0

1: Time

Duration of light after motion detection.

Property Value
Configuration ID config_1_2
Data Type INTEGER
Range 5 to 900
Default Value 180

2: Light

Light threshold [lx]:

Overview

0 – run Learn ambient light sequence. 2000 – is used as daylight (always night mode). Value can be controlled via potentiometer (if present on device) – potentiometer value is then used as the default value and any potentiometer movement rewrites the current setting.

Property Value
Configuration ID config_2_2
Data Type INTEGER
Range 2 to 2000
Default Value 2000

3: Dim

Night dim mode and time [min]: (only for SLAMP with DIM ability)

Overview

0 – off (dim = basic light completely disabled). 1-60 – time [minutes] (enabled in night mode, starts after lamp is switched off after motion detection). -1 – whole night (dim through the whole night when lamp is off). Dim mode is also disabled when local control is disabled as well as in Slave mode.

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 60
Default Value 0

4: Range

Motion Radar Range [cm]: (only for iHF sensor)

Overview

Value can be controlled via potentiometer (if present on device) – potentiometer value is then used as default value and any potentiometer movement rewrites the current setting.

Property Value
Configuration ID config_4_2
Data Type INTEGER
Range 100 to 500
Default Value 500

5: Sensity

Motion Radar Sensitivity [%]: (SLAMP+SPIR)

Overview

Value can be controlled via potentiometer (if present on device) – potentiometer value is then used as the default value and any potentiometer movement rewrites the current setting.

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 2 to 100
Default Value 100

8: Global_Light

Use external Ambient Light value:

Overview

When GLOBAL_LIGHT mode is ON – device overrides its own light sensor values and uses Light Report values from any Z-Wave light sensor instead – this has to be configured appropriately to send light automatically. If the last remote light level value is older than 30 minutes, the internal light value is used again until the next external value is received.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 1
Default Value 1

9: Slave_Mode

Disable local control:

Overview

Bit Field:

bit 7 6 5 4 3 2 1 0 Function - Don’t use button for lamp switching (STOGGLE) - - - “Stupid” mode Central unit checking in slave mode  Slave mode

“Stupid” mode (bit 2 = 1):

- has higher priority then slave mode - lamp/relay is permanently on (for simple power wall switch controlling)

Slave mode (bit 0 =1):

- only if included in Z-Wave network
- useful for controlling via third-party sensor - lamp/relay is directly controlled via Z-Wave, internal sensors are not used for controlling it

Central unit checking (bit 1 =1):

(useful especially for controlling via gateway)

When slave bit is 0:
- device signalises fail of lifeline connection (if this bit is zero, fail of lifeline connection is not signalised)

When slave bit is 1:
- device checks presence of Z-Wave device in lifeline group (gateway). If it is not present for 2 minutes (testing repeatedly every 30 seconds) device switches to normal mode in the same way as after the end of local disabled mode (ON_BEHAVIOUR)
- the device checks every 1 minute for recovery of lifeline connection
- if no lifeline specified
- it works in normal mode

Do not use button for lamp switching (bit 6 = 1):

only for STOGGLE variant
- disables button controlling device itself along with controlling group 5. When enabled also works in stand-alone.

Be careful with this option, device stops using its own motion sensor in Slave and “Stupid” mode.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 4
Default Value 2

10: Off_Behaviour

Off behaviour (timeout):

Overview

Behaviour after BASIC OFF (and similar commands). If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.

0 Lamp/Relay is switched off and remains so until any new motion event (local or remote) is received.

1 - 209 Lamp/Relay is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received. Timeout: 1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution 101..200 – 1 minute (101) to 100 minutes (200) 1-minute resolution 201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 Reserved

255 Lamp/relay is switched off for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Property Value
Configuration ID config_10_2
Data Type INTEGER
Range 0 to 255
Default Value 10

11: On_Behaviour

On behaviour (timeout):

Overview

Behaviour after BASIC ON (and similar commands). If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.

0 Lamp/relay is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

1 - 209 Lamp/relay is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation. Timeout: 1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution 101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution 201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

210 - 254 Reserved

255 Lamp/relay is switched on for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Property Value
Configuration ID config_11_2
Data Type INTEGER
Range 0 to 255
Default Value 255

12: On_Time_Over

On behaviour time over (timeout):

Overview

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or OFF_ON_BEHAVIOUR (0-209) to prevent staying ON forever when there is no motion.

0 No additional waiting for motion.

1 - 209 1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution 101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution 201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 Reserved

255 Never stop waiting for motion.

Property Value
Configuration ID config_12_2
Data Type INTEGER
Range 0 to 255
Default Value 204

13: On_Off_Behaviour

Sequence On-Off behaviour (timeout):

Overview

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands. The intention is to use a much longer timeout value than the time after a single ON command which should then be followed by a short timeout value. The behaviour is the same as for parameter 10 (OFF_LOCAL_DISABLE) except: 255 – device ignores ON - OFF sequence and uses OFF behaviour.

Property Value
Configuration ID config_13_2
Data Type INTEGER
Range 0 to 255
Default Value 204

14: Off_On_Behaviour

Sequence Off-On behaviour (timeout):

Overview

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands. The intention is to use a much longer timeout value than the time after a single OFF command which should then be followed by a short timeout value. The behaviour is the same as for parameter 11 (ON_LOCAL_DISABLE) except: 255 – device ignores OFF - ON sequence and uses ON behaviour.

Property Value
Configuration ID config_14_2
Data Type INTEGER
Range 0 to 255
Default Value 204

15: Sequence_Time

Sequence timing:

Overview

Time in [100 milliseconds] of maximum delay between BASIC ON and BASIC OFF (and vice versa) to consider this as a sequence. It is typically 1 second, but can be exceptionally longer due to retransmissions and overload – in this case, a longer interval can be allowed (up to 5 seconds).

Property Value
Configuration ID config_15_1
Data Type INTEGER
Range 10 to 50
Default Value 10

16: Motion_Disable

Motion Off behaviour (timeout):

Overview

Motion disable timeout after BASIC SET to motion endpoint when the internal motion sensor is not used for evaluating the behaviour of the lamp(SLAMP) relay(SPIR) and groups 2 and 3. Events are, however, still transmitted to the Lifeline, and the device can be controlled via remote motion sensors.

0 BASIC SET to motion sensor endpoint ignored, BASIC to root is mapped to relay endpoint, (SPIR) motion sensor still enabled

1 - 209 Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to motion endpoint. Timeout: 1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution 101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution 201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 Reserved

255 BASIC SET to motion endpoint ignored, motion sensor still disabled.

Property Value
Configuration ID config_16_2
Data Type INTEGER
Range 0 to 255
Default Value 209

1: General: Lifeline

Lifeline

Overview

Lifeline messages - Device Reset Locally (immediately) - Notifications: 0x09 (System) – Hardware failure with manufacturer proprietary code (0x03) 0x09 (System) – Software failure with manufacturer proprietary code (0x04) 0x07 (Home security) – Motion Begin event (0x08) 0x07 (Home security) – Motion End event (0x00, 0x08) - Binary Switch Report (SPIR) - Binary Switch Report (SBIN) - Multilevel Switch Report (SMUL) - Multilevel Sensor Report – value of internal ambient light sensor - Central scene notification (STOGGLE) Motion Begin and Motion End events are sent along with frames to group 3. If multichannel association is created the events are sent from motion sensor endpoint. Switch Report is sent immediately upon a change of status along with frames to group 2. If multichannel association is created the events are sent from lamp/relay endpoint. Multilevel Sensor Report is sent a maximum of once per 1 minute (if the value has changed by at least 3%) and a minimum of once per 15 minutes (if the value has not changed). If the ambient light value is old (cannot be measured because of permanent light), the value is not transmitted via lifeline. Multilevel Sensor Report can also be added to some other events to send in bulk. If multichannel association is created the events are sent from light sensor endpoint. Central scene notification is sent as reaction to user interaction. If multichannel association is created the events are sent from toggle button endpoint. All notifications to lifeline are sent as sensor states regardless of sensor settings and

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Control: Key01

On/Off control

Overview

Group 2 is used for directly controlling Z-Wave devices via BASIC SET commands through the evaluation of movement and light, as with internal use (so that all of these devices work together). This is intended for use especially with third-party devices that do not implement reactions for motion events. BASIC_SET and similar Z-Wave commands are not retransmitted intentionally to slaves and must be sent to slave devices via the controlling device simultaneously. Only for use in master-slave system, multi-device control is not possible. Group 2 is evaluated and frames are transmitted there also in SLAVE_ MODE, regardless of LOCAL_DISABLED state and when MOTION_ENABLE is off (not using internal motion sensor, just reacting to remote motion events in this case). If multichannel association is created the events are sent from motion sensor endpoint.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Notification: Motion

Motion Begin/End (PIR/radar/iHF)

Overview

Group 3 sends MOTION_BEGIN and MOTION_END frames. MOTION_BEGIN frame = Notification 0x07 (Home security) – Motion detection without location (0x08) MOTION_END frame = Notification 0x07 (Home security) – Event inactive (0x00, parameter 0x08)After the first motion detection, MOTION_BEGIN is sent. If continual movement is detected, MOTION_BEGIN is sent every 1 minute repeatedly. When motion ends, MOTION_END is sent 5 seconds after the last motion detection. Notification to group 3 is sent only when NIGHT_MODE = ON and MOTION_ ENABLE = ON, regardless of LOCAL_DISABLE state. All devices in a group should have the same TIME settings in order that they switch off at the same time. If multichannel association is created the events are sent from motion sensor endpoint.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Sensor: Luminescence

Ambient light

Overview

Ambient Light via Group 4 is intended to substitute locally measured LUX values in target devices – so that the network can have one source of ambient light value. Frames are sent a maximum of once per 2.5 minutes and a minimum of once per 15 minutes. When device already uses remote Ambient Light value, then this value is also retransmitted to group 4. All devices in such a group should have the same LIGHT (threshold) settings in order that night mode is detected at the same time. If multichannel association is created the events are sent from light sensor endpoint.

Property Value
Configuration ID group_4
Data Type TEXT
Range to

5: Control: Key02

On/Off button

Overview

Group 5 is used for directly controlling Z-Wave devices via BASIC SET commands by button. (STOGGLE) If multichannel association is created the events are sent from toggle button endpoint.

Property Value
Configuration ID group_5
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.