RS LED D2 Z-Wave Indoor LED-light with motion sensor

This describes the Z-Wave device RS LED D2 Z-Wave, manufactured by Steinel with the thing type UID of steinel_rsledd2_00_000.

Indoor LED-light with motion sensor

Overview

The sensor-switched indoor light contains an active motion detector.
The integrated HF sensor emits high-frequency electromagnetic waves (5.8 GHz) and receives their echo.
The change in echo caused by the slightest movement within the detection zone of the light is detected by the sensor.
A microprocessor then issues the switch command “switch light ON”.
Detection is possible through doors, panes of glass or thin walls.
This device can be integrated into the Smart Friends  system or any other Z-Wave network.
Z-Wave is a wireless standard for interconnecting Z-Wave devices.
The sensor parameters of the RS LED D2 indoor light can be used for wireless-based building automation.
Besides certified Z-Wave controllers, it is recommended  to use the Smart Friends box.
This smart-home control centre can be used for interconnecting Z-Wave products from STEINEL and the Smart Friends products from ABUS, Paulmann and Schellenberg.

The sensor-switched light can be put into service after mounting the enclosure and connecting to the mains power supply.
The light will also work without being integrated into a Z-Wave network.
In this case, the time setting is permanently set to 3 minutes.
When putting the light into operation, the light will switch OFF after the 10-second calibration phase and is then activated for sensor mode.
This light can now be integrated into the Z-Wave network.
The settings can be made via the control dials or via Z-Wave network.
The settings last selected will always be in effect regardless of whether they were made via the control dials or via Z-Wave network.

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers.
All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

Inclusion Information

These instructions for including and excluding Steinel Z-Wave products have been written for the Smart Friends system.
They may not always apply to other Z-Wave products.
You will find further details in the description of your Z-Wave controller.

To start the light’s inclusion or exclusion mode, briefly press button SET.

Following exclusion, all configuration parameters (time, sensitivity etc.) remain intact until next inclusion and the light now works in standalone mode – as a result, Z-Wave can also be used for the light’s standalone setting.

SET = Z-Wave button: Button for inclusion and exclusion as well as for returning the device  to the factory setting.

Exclusion Information

To start the light’s inclusion or exclusion mode, briefly press button SET.

Channels

The following table summarises the channels available for the RS LED D2 Z-Wave Indoor LED-light with motion sensor.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Scene Number scene_number scene_number   Number
Binary Sensor sensor_binary sensor_binary Door Switch
Sensor (luminance) sensor_luminance sensor_luminance Temperature Number
Alarm (system) alarm_system alarm_system   Switch
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Switch 1 switch_binary1 switch_binary Switch Switch
Scene Number 1 scene_number1 scene_number   Number
Alarm (burglar) 2 alarm_burglar2 alarm_burglar Door Switch

Device Configuration

The following table provides a summary of the configuration parameters available in the RS LED D2 Z-Wave Indoor LED-light with motion sensor. Detailed information on each parameter can be found below.

Parameter Description
1: Time [s] Duration of light after motion detection.
2: Light threshold [lx] LIGHT
5: Motion Radar Sensitivity [%] SENSITIVITY
6: Brightness measuring interval [min] (only SLAMP)
8: Use external Ambient Light value GLOBAL_LIGHT
9: Disable local control SLAVE_MODE
10: Off behaviour (timeout) OFF_BEHAVIOUR
11: On behaviour (timeout) ON_BEHAVIOUR
12: On behaviour time over (timeout) ON_TIME_OVER
13: Sequence On-Off behaviour (timeout) ON_OFF_ BEHAVIOUR
14: Sequence Off-On behaviour (timeout) OFF_ON_ BEHAVIOUR
15: Sequence timing SEQUENCE_TIME
16: Motion Off behaviour (timeout) MOTION_ DISABLE
0: Root Root
1: Lifeline Lifeline
2: Control: Key01 On/Off control (Never ever add controller, only third-party devices!)
3: Motion Begin/End (PIR/radar/iHF) Notification: Motion
4: Ambient light Sensor: Luminescence

1: Time [s]

Duration of light after motion detection.

Property Value
Configuration ID config_1_2
Data Type INTEGER
Range 5 to 900
Default Value 180

2: Light threshold [lx]

LIGHT

Overview

0      – run Learn ambient light sequence.
2000 – is used as daylight (always night mode).

Value can be controlled via potentiometer (if present on device) – potentiometer value is then used as the default value and any potentiometer movement rewrites the current setting

Property Value
Configuration ID config_2_2
Data Type INTEGER
Range 2 to 2000
Default Value 2000

5: Motion Radar Sensitivity [%]

SENSITIVITY

Overview

Value can be controlled via potentiometer (if present on device) – potentiometer value is then used as the default value and any potentiometer movement rewrites the current setting.

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 2 to 100
Default Value 100

6: Brightness measuring interval [min]

(only SLAMP)

Overview

Interval for measuring ambient light when lamp is on (lamp switches off briefly and measures). 0 = function is off.

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 5 to 120
Default Value 0

8: Use external Ambient Light value

GLOBAL_LIGHT

Overview

When GLOBAL_LIGHT mode is ON – device overrides its own light sensor values and uses Light Report values from any Z-Wave light sensor instead – this has to be configured appropriately to send light automatically.

If the last remote light level value is older than 30 minutes, the internal light value is used again until the next external value is received.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 1
Default Value 1

9: Disable local control

SLAVE_MODE

Overview

“Stupid” mode (bit 2 = 1):
  - has higher priority then slave mode
  - lamp/relay is permanently on (for simple power wall switch controlling)

Slave mode (bit 0 =1):
  - only if included in Z-Wave network
  - useful for controlling via third-party sensor
  - lamp/relay is directly controlled via Z-Wave, internal sensors are not used for controlling it

Central unit checking (bit 1 =1): (useful especially for controlling via gateway)
  When slave bit is 0:
  - device signalises fail of lifeline connection (if this bit is zero, fail of lifeline connection is not signalised)

  When slave bit is 1:
  - device checks presence of Z-Wave device in lifeline group (gateway).
    If it is not present for 2 minutes (testing repeatedly every 30 seconds)
    device switches to normal mode in the same way as after the end of
    local disabled mode (ON_BEHAVIOUR)
  - the device checks every 1 minute for recovery of lifeline connection
  - if no lifeline specified - it works in normal mode

Do not use button for lamp switching (bit 6 = 1): only for STOGGLE variant
  - disables button controlling device itself along with controlling group 5.

    When enabled also works in stand-alone.

Be careful with this option, device stops using its own motion sensor in Slave and “Stupid” mode.

bit field:

7 - no Function

6 - Don’t use button for lamp - switching (STOGGLE)

4 - no Function

3 - no Function

2 - “Stupid” mode

1 - Central unit checking in slave mode

0 - Slave mode

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 4
Default Value 2

10: Off behaviour (timeout)

OFF_BEHAVIOUR

Overview

Behaviour after BASIC OFF (and similar commands).
If a transition (even with zero change) with a non-default duration is to be pro-
cessed, the transition cannot be interrupted by any motion event in any case.

0 = Lamp/Relay is switched off and remains so until any new motion event (local or remote) is received.

1 - 209 = Lamp/Relay is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received.
    Timeout:
    1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
    101..200 – 1 minute (101) to 100 minutes (200) 1-minute resolution
    201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = Lamp/relay is switched off for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Property Value      
Configuration ID config_10_2      
Data Type INTEGER   Default Value 10
Options Lamp/relay is switched off for TIME (cfg 1) (255)      

11: On behaviour (timeout)

ON_BEHAVIOUR

Overview

Behaviour after BASIC ON (and similar commands).
If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.

0 = Lamp/relay is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation.
Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

1 - 209 = Lamp/relay is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation.
    Timeout:
    1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
    101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
    201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution
Notice – during the day, this mode cannot be ended remotely due to motion events not being transmitted – only via local motion sensor if enabled.

210 - 254 = Reserved

255 = Lamp/relay is switched on for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Property Value
Configuration ID config_11_2
Data Type INTEGER
Range 2 to 209
Default Value 255

12: On behaviour time over (timeout)

ON_TIME_OVER

Overview

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or
OFF_ON_BEHAVIOUR (0-209) to prevent staying ON forever when there is
no motion.

0 = No additional waiting for motion.

1 - 209 =  1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
                  101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
                  201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = Never stop waiting for motion.

Property Value
Configuration ID config_12_2
Data Type INTEGER
Range 0 to 209
Default Value 204

13: Sequence On-Off behaviour (timeout)

ON_OFF_ BEHAVIOUR

Overview

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands.
The intention is to use a much longer timeout value than the time after a
single ON command which should then be followed by a short timeout value.
The behaviour is the same as for parameter 10 (OFF_LOCAL_DISABLE)
except: 255 – device ignores ON - OFF sequence and uses OFF behaviour.

Property Value
Configuration ID config_13_2
Data Type INTEGER
Range 0 to 209
Default Value 204

14: Sequence Off-On behaviour (timeout)

OFF_ON_ BEHAVIOUR

Overview

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands.
The intention is to use a much longer timeout value than the time after a sin-
gle OFF command which should then be followed by a short timeout value.
The behaviour is the same as for parameter 11 (ON_LOCAL_DISABLE)
except: 255 – device ignores OFF - ON sequence and uses ON behaviour.

Property Value
Configuration ID config_14_2
Data Type INTEGER
Range 0 to 209
Default Value 204

15: Sequence timing

SEQUENCE_TIME

Overview

Time in [100 milliseconds] of maximum delay between BASIC ON and BASIC
OFF (and vice versa) to consider this as a sequence. It is typically 1 second,
but can be exceptionally longer due to retransmissions and overload – in this
case, a longer interval can be allowed (up to 5 seconds).

Property Value
Configuration ID config_15_1
Data Type INTEGER
Range 10 to 50
Default Value 10

16: Motion Off behaviour (timeout)

MOTION_ DISABLE

Overview

Motion disable timeout after BASIC SET to motion endpoint when the inter-
nal motion sensor is not used for evaluating the behaviour of the lamp (SLAMP)
relay (SPIR) and groups 2 and 3. Events are, however, still transmitted to the
Lifeline, and the device can be controlled via remote motion sensors.

0 = BASIC SET to motion sensor endpoint ignored, BASIC to root is
mapped to relay endpoint, (SPIR) motion sensor still enabled

1 - 209 = Internal motion sensor is disabled for specified timeout after BASIC
SET 0x00 to motion endpoint.
Timeout:
1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = BASIC SET to motion endpoint ignored, motion sensor still disabled.

Property Value
Configuration ID config_16_2
Data Type INTEGER
Range 2 to 209
Default Value 0

0: Root

Root

Property Value
Configuration ID group_0
Data Type TEXT
Range to

1: Lifeline

Lifeline

Overview

Lifeline messages

 - Device Reset Locally (immediately)
 - Notifications:
    0x09 (System) – Hardware failure with manufacturer proprietary code (0x03)
    0x09 (System) – Software failure with manufacturer proprietary code (0x04)
    0x07 (Home security) – Motion Begin event (0x08)
    0x07 (Home security) – Motion End event (0x00, 0x08)
- Binary Switch Report (SPIR)
- Binary Switch Report (SBIN)
- Multilevel Switch Report (SMUL)
- Multilevel Sensor Report – value of internal ambient light sensor
- Central scene notification (STOGGLE)

Motion Begin and Motion End events are sent along with frames to group 3.

If multichannel association is created the events are sent from motion sensor endpoint.

Switch Report is sent immediately upon a change of status along with frames to group 2.

If multichannel association is created the events are sent from lamp/relay endpoint.

Multilevel Sensor Report is sent a maximum of once per 1 minute (if the value has changed by at least 3%) and a minimum of once per 15 minutes (if the value has not changed).

If the ambient light value is old (cannot be measured because of permanent light), the value is not transmitted via lifeline.

Multilevel Sensor Report can also be added to some other events to send in bulk.

If multichannel association is created the events are sent from light sensor endpoint.

Central scene notification is sent as reaction to user interaction.

If multichannel association is created the events are sent from toggle button endpoint.

All notifications to lifeline are sent as sensor states regardless of sensor settings and states as SLAVE_MODE, LOCAL_DISABLED and MOTION_ENABLE.

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Control: Key01

On/Off control (Never ever add controller, only third-party devices!)

Overview

Group 2 is used for directly controlling Z-Wave devices via BASIC SET commands through the evaluation of movement and light, as with internal use (so that all of these devices work together).

This is intended for use especially with third-party devices that do not implement reactions for motion events.

BASIC_SET and similar Z-Wave commands are not retransmitted intentionally to slaves and must be sent to slave devices via the controlling device simultaneously.

Only for use in master-slave system, multi-device control is not possible.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Motion Begin/End (PIR/radar/iHF)

Notification: Motion

Overview

Group 3 sends MOTION_BEGIN and MOTION_END frames.

  MOTION_BEGIN frame = Notification 0x07 (Home security) – Motion detection without location (0x08)
  MOTION_END frame = Notification 0x07 (Home security) – Event inactive (0x00, parameter 0x08)

After the first motion detection, MOTION_BEGIN is sent.

If continual movement is detected, MOTION_BEGIN is sent every 1 minute repeatedly.

When motion ends, MOTION_END is sent 5 seconds after the last motion detection.

Notification to group 3 is sent only when NIGHT_MODE = ON and MOTION_ENABLE = ON, regardless of LOCAL_DISABLE state.

All devices in a group should have the same TIME settings in order that they switch off at the same time.

If multichannel association is created the events are sent from motion sensor endpoint.

Group 2 is evaluated and frames are transmitted there also in SLAVE_MODE, regardless of LOCAL_DISABLED state and when MOTION_ENABLE is off (not using internal motion sensor, just reacting to remote motion events in this case).

If multichannel association is created the events are sent from motion sensor endpoint.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Ambient light

Sensor: Luminescence

Overview

Ambient Light via Group 4 is intended to substitute locally measured LUX
values in target devices – so that the network can have one source of ambient light value.

Frames are sent a maximum of once per 2.5 minutes and a minimum of once per 15 minutes.

When device already uses remote Ambient Light value, then this value is also retransmitted to group 4.

All devices in such a group should have the same LIGHT (threshold) settings in order that night mode is detected at the same time.

Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.