XLED Home 2 PIR sensor with relay and light

This describes the Z-Wave device XLED Home 2, manufactured by Steinel with the thing type UID of steinel_xledhome2_00_000.

PIR sensor with relay and light

Channels

The following table summarises the channels available for the XLED Home 2 PIR sensor with relay and light.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Scene Number scene_number scene_number   Number
Binary Sensor sensor_binary sensor_binary Door Switch
Sensor (luminance) sensor_luminance sensor_luminance Temperature Number
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Alarm (system) alarm_system alarm_system   Switch
Control: Key01 lamp (on/off) switch_binary1 switch_binary Switch Switch
Scene Number 1 scene_number1 scene_number   Number
Alarm (burglar) motion alarm_burglar2 alarm_burglar Door Switch
Sensor (luminance)2 sensor_luminance3 sensor_luminance Temperature Number

Device Configuration

The following table provides a summary of the configuration parameters available in the XLED Home 2 PIR sensor with relay and light. Detailed information on each parameter can be found below.

Parameter Description
1: Time Duration of light after motion detection.
2: LIGHT Light threshold [lx]:
5: SENSITIVITY Motion Radar Sensitivity [%]
6: BRIGHTNES MEAS 1 INTERVAL Brightness measuring interval [min]
8: GLOBAL_LIGHT Use external Ambient Light value
9: SLAVE_MODE Disable local control
10: (OFF_BEHAVIOUR) Off behaviour (timeout)
11: ON_BEHAVIOUR On behaviour (timeout)
12: ON_TIME_OVER On behaviour time over (timeout)
13: ON_OFF_ BEHAVIOUR Sequence On-Off behaviour (timeout)
14: OFF_ON_ BEHAVIOUR Sequence Off-On behaviour (timeout)
15: SEQUENCE_ TIME Sequence timing
16: MOTION_ DISABLE Motion Off behaviour (timeout)
1: Lifeline Lifeline
2: Control: Key01 On/Off control (Never ever add controller, only third-party devices!)
3: Motion Begin/End (PIR/radar/iHF) Notification: Motion
4: Ambient light Sensor: Luminescence

1: Time

Duration of light after motion detection.

Property Value
Configuration ID config_1_2
Data Type INTEGER
Range 5 to 900
Default Value 180

2: LIGHT

Light threshold [lx]:

Overview

0          – run Learn ambient light sequence.
2000 – is used as daylight (always night mode).
Value can be controlled via potentiometer (if present on device) –
potentiometer value is then used as the default value and any
potentiometer movement rewrites the current setting

Property Value
Configuration ID config_2_2
Data Type INTEGER
Range 2 to 2000
Default Value 2000

5: SENSITIVITY

Motion Radar Sensitivity [%]

Overview

Value can be controlled via potentiometer (if present on device) – potentiom-
eter value is then used as the default value and any potentiometer movement
rewrites the current setting.

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 2 to 100
Default Value 100

6: BRIGHTNES MEAS 1 INTERVAL

Brightness measuring interval [min]

Overview

nterval for measuring ambient light when lamp is on (lamp switches off
briefly and measures). 0 = function is off.

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 5 to 120
Default Value 0

8: GLOBAL_LIGHT

Use external Ambient Light value

Overview

When GLOBAL_LIGHT mode is ON – device overrides its own light sensor
values and uses Light Report values from any Z-Wave light sensor instead –
this has to be configured appropriately to send light automatically.
If the last remote light level value is older than 30 minutes, the internal light
value is used again until the next external value is received.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 1
Default Value 1

9: SLAVE_MODE

Disable local control

Overview

“Stupid” mode (bit 2 = 1):
- has higher priority then slave mode
- lamp/relay is permanently on (for simple power wall switch controlling)

Slave mode (bit 0 =1):
- only if included in Z-Wave network
- useful for controlling via third-party sensor
- lamp/relay is directly controlled via Z-Wave, internal sensors are not used
for controlling it

Central unit checking (bit 1 =1): (useful especially for controlling via gateway)
When slave bit is 0:
- device signalises fail of lifeline connection (if this bit is zero, fail of lifeline
connection is not signalised)

When slave bit is 1:
- device checks presence of Z-Wave device in lifeline group (gateway).
If it is not present for 2 minutes (testing repeatedly every 30 seconds)
device switches to normal mode in the same way as after the end of
local disabled mode (ON_BEHAVIOUR)
- the device checks every 1 minute for recovery of lifeline connection
- if no lifeline specified - it works in normal mode

Do not use button for lamp switching (bit 6 = 1): only for STOGGLE variant
- disables button controlling device itself along with controlling group 5.
When enabled also works in stand-alone.

Be careful with this option, device stops using its own motion sensor in
Slave and “Stupid” mode.

bit field:

bit 7 6 5 4 3 2 1 0 Function - Don’t use
button
for lamp -
switching
(STOGGLE) - - - “Stupid”
mode Central
unit
checking
in slave
mode Slave
mode

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 4
Default Value 2

10: (OFF_BEHAVIOUR)

Off behaviour (timeout)

Overview

Behaviour after BASIC OFF (and similar commands).
If a transition (even with zero change) with a non-default duration is to be pro-
cessed, the transition cannot be interrupted by any motion event in any case.

0 = Lamp/Relay is switched off and remains so until any new motion
event (local or remote) is received.

1 - 209 = Lamp/Relay is switched off and remains so until after a specified
timeout once a new motion event (local or remote) is received.
Timeout:
1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
101..200 – 1 minute (101) to 100 minutes (200) 1-minute resolution
201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = Lamp/relay is switched off for TIME (cfg 1). It does not wait for a
motion event and works normally via current motion evaluation.

Property Value      
Configuration ID config_10_2      
Data Type INTEGER      
Range 0 to 209   Default Value 10
Options Lamp/relay is switched off for TIME (cfg 1) (255)      

11: ON_BEHAVIOUR

On behaviour (timeout)

Overview

Behaviour after BASIC ON (and similar commands).
If a transition (even with zero change) with a non-default duration is to be
processed, the transition cannot be interrupted by any motion event in any
case.

0 = Lamp/relay is switched on and remains so until any new motion
event (local or remote) is received. It then works normally via current
motion evaluation.
Notice – during the day, this mode cannot be ended remotely due
to motion events not being transmitted – only via local motion sen-
sor if enabled.

1 - 209 = Lamp/relay is switched on and remains so until after a specified
timeout once a new motion event (local or remote) is received. It then
works normally via current motion evaluation.
Timeout:
1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution
Notice – during the day, this mode cannot be ended remotely due to
motion events not being transmitted – only via local motion sensor if
enabled.

210 - 254 = Reserved

255 = Lamp/relay is switched on for TIME (cfg 1). It does not wait for a
motion event and works normally via current motion evaluation.

Property Value
Configuration ID config_11_2
Data Type INTEGER
Range 2 to 209
Default Value 255

12: ON_TIME_OVER

On behaviour time over (timeout)

Overview

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or
OFF_ON_BEHAVIOUR (0-209) to prevent staying ON forever when there is
no motion.

0 = No additional waiting for motion.

1 - 209 =  1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
                  101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
                  201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = Never stop waiting for motion.

Property Value
Configuration ID config_12_2
Data Type INTEGER
Range 0 to 209
Default Value 204

13: ON_OFF_ BEHAVIOUR

Sequence On-Off behaviour (timeout)

Overview

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands.
The intention is to use a much longer timeout value than the time after a
single ON command which should then be followed by a short timeout value.
The behaviour is the same as for parameter 10 (OFF_LOCAL_DISABLE)
except: 255 – device ignores ON - OFF sequence and uses OFF behaviour.

Property Value
Configuration ID config_13_2
Data Type INTEGER
Range 0 to 209
Default Value 204

14: OFF_ON_ BEHAVIOUR

Sequence Off-On behaviour (timeout)

Overview

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands.
The intention is to use a much longer timeout value than the time after a sin-
gle OFF command which should then be followed by a short timeout value.
The behaviour is the same as for parameter 11 (ON_LOCAL_DISABLE)
except: 255 – device ignores OFF - ON sequence and uses ON behaviour.

Property Value
Configuration ID config_14_2
Data Type INTEGER
Range 0 to 209
Default Value 204

15: SEQUENCE_ TIME

Sequence timing

Overview

Time in [100 milliseconds] of maximum delay between BASIC ON and BASIC
OFF (and vice versa) to consider this as a sequence. It is typically 1 second,
but can be exceptionally longer due to retransmissions and overload – in this
case, a longer interval can be allowed (up to 5 seconds).

Property Value
Configuration ID config_15_1
Data Type INTEGER
Range 10 to 50
Default Value 10

16: MOTION_ DISABLE

Motion Off behaviour (timeout)

Overview

Motion disable timeout after BASIC SET to motion endpoint when the inter-
nal motion sensor is not used for evaluating the behaviour of the lamp (SLAMP)
relay (SPIR) and groups 2 and 3. Events are, however, still transmitted to the
Lifeline, and the device can be controlled via remote motion sensors.

0 = BASIC SET to motion sensor endpoint ignored, BASIC to root is
mapped to relay endpoint, (SPIR) motion sensor still enabled

1 - 209 = Internal motion sensor is disabled for specified timeout after BASIC
SET 0x00 to motion endpoint.
Timeout:
1..100 – 1 second (1) to 100 seconds (100) in 1-second resolution
101..200 – 1 minute (101) to 100 minutes (200) in 1-minute resolution
201..209 – 1 hour (201) to 9 hours (209) in 1-hour resolution

210 - 254 = Reserved

255 = BASIC SET to motion endpoint ignored, motion sensor still disabled.

Property Value
Configuration ID config_16_2
Data Type INTEGER
Range 2 to 209
Default Value 0

1: Lifeline

Lifeline

Overview

- Device Reset Locally (immediately)
- Notifications:
0x09 (System) – Hardware failure with manufacturer proprietary code (0x03)
0x09 (System) – Software failure with manufacturer proprietary code (0x04)
0x07 (Home security) – Motion Begin event (0x08)
0x07 (Home security) – Motion End event (0x00, 0x08)
- Binary Switch Report (SPIR)
- Binary Switch Report (SBIN)
- Multilevel Switch Report (SMUL)
- Multilevel Sensor Report – value of internal ambient light sensor
- Central scene notification (STOGGLE)
Motion Begin and Motion End events are sent along with frames to group 3.
If multichannel association is created the events are sent from motion sensor
endpoint.
Switch Report is sent immediately upon a change of status along with
frames to group 2. If multichannel association is created the events are sent
from lamp/relay endpoint.
Multilevel Sensor Report is sent a maximum of once per 1 minute
(if the value has changed by at least 3%) and a minimum of once per 15 min-
utes (if the value has not changed). If the ambient light value is old (cannot
be measured because of permanent light), the value is not transmitted via
lifeline. Multilevel Sensor Report can also be added to some other events to
send in bulk. If multichannel association is created the events are sent from
light sensor endpoint.
Central scene notification is sent as reaction to user interaction. If multichan-
nel association is created the events are sent from toggle button endpoint.

All notifications to lifeline are sent as sensor states regardless of sensor
settings and states as SLAVE_MODE, LOCAL_DISABLED and MOTION_
ENABLE

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Control: Key01

On/Off control (Never ever add controller, only third-party devices!)

Overview

Group 2 is used for directly controlling Z-Wave devices via BASIC SET com-
mands through the evaluation of movement and light, as with internal use
(so that all of these devices work together). This is intended for use especially
with third-party devices that do not implement reactions for motion events.
BASIC_SET and similar Z-Wave commands are not retransmitted intention-
ally to slaves and must be sent to slave devices via the controlling device
simultaneously. Only for use in master-slave system, multi-device control is
not possible.
Group 2 is evaluated and frames are transmitted there also in SLAVE_
MODE, regardless of LOCAL_DISABLED state and when MOTION_ENABLE
is off (not using internal motion sensor, just reacting to remote motion events
in this case).
If multichannel association is created the events are sent from motion sensor
endpoint.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Motion Begin/End (PIR/radar/iHF)

Notification: Motion

Overview

Group 3 sends MOTION_BEGIN and MOTION_END frames.
MOTION_BEGIN frame = Notification 0x07 (Home security) –
Motion detection without location (0x08)
MOTION_END frame = Notification 0x07 (Home security) –
Event inactive (0x00, parameter 0x08)

After the first motion detection, MOTION_BEGIN is sent. If continual move-
ment is detected, MOTION_BEGIN is sent every 1 minute repeatedly. When
motion ends, MOTION_END is sent 5 seconds after the last motion detec-
tion.
Notification to group 3 is sent only when NIGHT_MODE = ON and MOTION_
ENABLE = ON, regardless of LOCAL_DISABLE state.
All devices in a group should have the same TIME settings in order that they
switch off at the same time.
If multichannel association is created the events are sent from motion sensor
endpoint.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Ambient light

Sensor: Luminescence

Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.