The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

TZ65D Dual Paddle Wall Dimmer

This describes the Z-Wave device TZ65D, manufactured by TKB Home with the thing type UID of tkb_tz65d_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

The TZ65D supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the TZ65D -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 9 configuration parameters available in the TZ65D. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Ignore start level Ignore start level when transmitting a dim command to the dimmer
2 Suspend Group 4 Setting this parameter will disable transmitting commands to devices in association group 4
3 Blue LED light Behavior Defines the behavior of the blue LED. Default is Night Light mode where LED is on when switch is off
4 Invert Switch To change the top of the switch to off and the botton to on
14 Enable Shade Control Group 2 Enable the control of shade devices in association group 2 when this option is activated
15 Enable Shade Control Group 3 Enable the control of shade devices in association group 3 when this option is activated
19 Blue LED light behavior on transmission Defines the behavior of the blue LED when transmission of data
20 Poll Group 2 Interval (minutes) Polling Interval in minutes (default 2)
22 Poll Group 2 Defines if the device will poll association Group 2 at the interval defined in parameter 20
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Ignore start level

Ignore start level when transmitting a dim command to the dimmer

The following option values may be configured -:

Value Description
0 Ignore
1 Don’t ignore

The manufacturer defined default value is 1 (Don’t ignore).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Suspend Group 4

Setting this parameter will disable transmitting commands to devices in association group 4

The following option values may be configured -:

Value Description
0 Transmit to group 4
1 Disable transmitting to group 4

The manufacturer defined default value is 0 (Transmit to group 4).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Blue LED light Behavior

Defines the behavior of the blue LED. Default is Night Light mode where LED is on when switch is off

The following option values may be configured -:

Value Description
0 Led on when switch on
1 Night light

The manufacturer defined default value is 0 (Led on when switch on).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Invert Switch

To change the top of the switch to off and the botton to on

The following option values may be configured -:

Value Description
0 ON on top
1 OFF on top

The manufacturer defined default value is 0 (ON on top).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 14: Enable Shade Control Group 2

Enable the control of shade devices in association group 2 when this option is activated

The following option values may be configured -:

Value Description
0 Inactive
1 Shade Control

The manufacturer defined default value is 0 (Inactive).

This parameter has the configuration ID config_14_1 and is of type INTEGER.

Parameter 15: Enable Shade Control Group 3

Enable the control of shade devices in association group 3 when this option is activated

The following option values may be configured -:

Value Description
0 Inactive
1 Shade Control

The manufacturer defined default value is 0 (Inactive).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 19: Blue LED light behavior on transmission

Defines the behavior of the blue LED when transmission of data

The following option values may be configured -:

Value Description
0 LED does not blinks on activity
1 LED blinks on activity all the time
2 LED blinks on activity 1 second

The manufacturer defined default value is 2 (LED blinks on activity 1 second).

This parameter has the configuration ID config_19_1 and is of type INTEGER.

Parameter 20: Poll Group 2 Interval (minutes)

Polling Interval in minutes (default 2)

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 2.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Parameter 22: Poll Group 2

Defines if the device will poll association Group 2 at the interval defined in parameter 20

The following option values may be configured -:

Value Description
0 Disabled
1 Enabled

The manufacturer defined default value is 1 (Enabled).

This parameter has the configuration ID config_22_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The TZ65D supports 4 association groups.

Group 1: Group 1

This group supports 5 nodes.

Group 2: Group 2

This group supports 5 nodes.

Group 3: Group 3

This group supports 5 nodes.

Group 4: Group 4

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V0  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.