The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

Vitrum Satellite VI Vitrum touch switch satellite 6 buttons

This describes the Z-Wave device Vitrum Satellite VI, manufactured by VDA with the thing type UID of vda_satellitevi_00_000.

The Vitrum Satellite VI supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

When the device is in the stand-alone mode and is not included in a Z-Wave network the illuminated ring around the touch keys will light red for a moment when passing from one mode to another.

Each button can be configured in 4 different modes. Press the 2 service buttons (left and right each) for at least 8 seconds. Buttons will start to flash and the color of the flashing ring will indicate the channel setting:

- Yellow: for association with On-Off Modules, toggle-button function (BASIC)

- Red: for association with On-Off Modules, push-button function (BASIC)

- Magenta: for association with Roller Blinds, 2 buttons will start flashing together for up and down movement (SWITCH_MULTILEVEL)

- Green: for association with Dimmer Modules (SWITCH_MULTILEVEL)

After mode selection, please proceed with inclusion process.

Inclusion Information

With the controller in the inclusion mode, press any of the touch keys on the device. Vitrum indicates that it has been included to the network by flashing the yellow LEDs three times and switching on all the lights connected to the unit.

Exclusion Information

Press and hold the leftmost touch key for at least 8 seconds. The device will flash red three times and sound an acoustic signal to indicate that the original factory setting has been restored.

Channels

The following table summarises the channels available for the Vitrum Satellite VI -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Dimmer switch_dimmer DimmableLight Dimmer
Dimmer 1 switch_dimmer1 DimmableLight Dimmer
Dimmer 2 switch_dimmer2 DimmableLight Dimmer
Dimmer 3 switch_dimmer3 DimmableLight Dimmer
Dimmer 4 switch_dimmer4 DimmableLight Dimmer
Dimmer 5 switch_dimmer5 DimmableLight Dimmer
Dimmer 6 switch_dimmer6 DimmableLight Dimmer

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 1

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer1 channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 2

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer2 channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 3

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer3 channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 4

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer4 channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 5

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer5 channel supports the Dimmer item and is in the DimmableLight category.

Dimmer 6

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer6 channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The device has no configuration parameters configured.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The Vitrum Satellite VI supports 6 association groups.

Group 1: Button channel 1

This group supports 5 nodes.

Group 2: Button channel 2

This group supports 5 nodes.

Group 3: Button channel 3

This group supports 5 nodes.

Group 4: Button channel 4

This group supports 5 nodes.

Group 5: Button channel 5

This group supports 5 nodes.

Group 6: Button channel 6

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_NODE_NAMING_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V1| | | COMMAND_CLASS_INDICATOR_V1| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 3

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 4

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 5

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC| | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 6

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1 Linked to BASIC
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.