MT-100 Motion and Light Mini Sensor

This describes the Z-Wave device MT-100, manufactured by Vemmio with the thing type UID of vemmio_mt100_00_000.

Motion and Light Mini Sensor

Overview

Motion Mini Sensor provides accurate motion and illumination level detection. When integrated with your controller - wireless notifications, low battery alerts, custom automation scenarios based on both light and motion triggers become available. For example, when motion is detected, the controller will send an alert to any smartphone, set off an alarm or trigger a lighting scene. The sensor works with any Z-Wave-certified controller 

Wireless standard Z-Wave Plus Frequency 868.40 MHz Network range 30 m line of sight Operating temperature 0°C ~ 40°C Illumination measurement range 0 ~ 8500 lux Movement Sensor Measurement range 6 m Battery CR123A 3V Battery >2 years, low power indication.

Factory reset: press and hold the Z-Wave button for at least 10 seconds until the LED indicator flashes once (it may then flash 5 times to indicate the device is no longer part of Z-Wave network). Release the button.

Inclusion Information

When prompted by the controller, press quickly one of the Z-wave button 3 times in a row. The sensor should be included in 5 seconds. The sensor should appear on your controller’s device list.

Exclusion Information

When prompted by the controller, press quickly one of the Z-wave button 3 times in a row. The sensor should be excluded in 5 seconds. The sensor should appear on your controller’s device list.

Wakeup Information

You can press the button once to wake up the device and send wakeup notification to controller -the LED will flash once.

Channels

The following table summarises the channels available for the MT-100 Motion and Light Mini Sensor.

Channel Channel Id Channel Type UID Category Item Type
Binary Sensor sensor_binary sensor_binary Door Switch
Sensor (luminance) sensor_luminance sensor_luminance Temperature Number
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the MT-100 Motion and Light Mini Sensor. Detailed information on each parameter can be found below.

Parameter Description
1: Sensitivity Level Setting This parameter defines the sensitivity of PIR detector
2: On/Off Duration how long the associated devices should stay ON status
3: Basic Set Level value when PIR detector is triggered and Basic Set command sent
4: PIR Detecting Function Enabled/Disabled enabled or disabled the PIR
5: Ambient illumination Lux Level Set a lux level value which determines when the light sensor is activated
6: Retrigger Interval Setting Interval of being re-triggered after the PIR detector has been triggered.
7: Light Sensor Polling Interva Time Set the light sensor measure ambient illumination level interval time
8: Lux Level Function Enable  
9: Ambient illumination Lux Level Report  
10: Led Flash Enable This parameter defines the Led on/off enable
1: GROUP 1 lifeline service that assigned to Motion detector status
2: GROUP 2 allows for sending control commands to associated devices
3: GROUP 3 allows for Send Notification to associated devices
4: GROUP 4 allows for Send Sensor Binary Report to associated devices

1: Sensitivity Level Setting

This parameter defines the sensitivity of PIR detector

Overview

This parameter defines the sensitivity of PIR detector, it is recommended to test the detector with movements from a farthest end of the coverage area at first time of use. If movements cannot be detected sensitively, simply adjust the sensitivity level with this parameter.

This Parameter can be configured with the value of 8 through 255, where 8 means high sensitivity and 255 means lowest sensitivity.

Property Value
Configuration ID config_1_1
Data Type INTEGER
Range 8 to 255
Default Value 12

2: On/Off Duration

how long the associated devices should stay ON status

Overview

This parameter can be determined how long the associated devices should stay ON status. For instance, this parameter is set to 30(second), the PIR detector will send a BASIC_SET Command to an associated device with value basic set level if PIR detector is triggered and the associated device will be turned on 30(second) before it is turned off. This Parameter value must be large than Parameter 6#. If user set this parameter to default by Configure CC, the parameter #6 will be set to default value

Property Value
Configuration ID config_2_2
Data Type INTEGER
Range 5 to 600
Default Value 30

3: Basic Set Level

value when PIR detector is triggered and Basic Set command sent

Overview

Valid Values: (0 – 99) 

0 – OFF , 255 - ON 

Basic Set Command will be sent where contains a value when PIR detector is triggered, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set Command of which value is decisive as to how bright of dim level of lamp module shall be. This Parameter is used to some associated devices

Property Value      
Configuration ID config_3_1      
Data Type INTEGER      
Range 0 to 99   Default Value 255
Options OFF (255)      

4: PIR Detecting Function Enabled/Disabled

enabled or disabled the PIR

Overview

Valid Values: 0 – Disable PIR, 255 – Enable PIR

This parameter can be enabled or disabled the PIR detector detecting function.

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 255
Options Disable PIR (0)      
  Enable PIR (255)      

5: Ambient illumination Lux Level

Set a lux level value which determines when the light sensor is activated

Overview

This parameter can be set a lux level value which determines when the light sensor is activated. If the ambient illumination level falls below this value and a person moves across or within the detected area , PIR detector will send a Z-Wave ON command(i.e. BASIC_SET (value = parameter 3) to an associated device and activate i

Property Value
Configuration ID config_5_2
Data Type INTEGER
Range 0 to 1000
Default Value 100

6: Retrigger Interval Setting

Interval of being re-triggered after the PIR detector has been triggered.

Overview

This Parameter can be used to adjust the interval of being re-triggered after the PIR detector has been triggered.

This Parameter value must be less than Parameter 2#. If user set this parameter to default by Configure CC, the para

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 0 to 8
Default Value 8

7: Light Sensor Polling Interva Time

Set the light sensor measure ambient illumination level interval time

Overview

This Parameter can be set the light sensor measure ambient illumination level

interval time. NOTE: This Value Must Be less than Wakeup Interval Time

Property Value
Configuration ID config_7_2
Data Type INTEGER
Range 60 to 36000
Default Value 180

8: Lux Level Function Enable

Overview

If this parameter is set to ‘1’, and when Lux level less than the value define by parameter #5, PIR detector will send a BASIC_SET command frame (i.e. BASIC_SET (value = parameter 3) to an associated device and activate it. If Lux Level greater than the value define by parameter #5, PIR detector will not send a BASIC_SET command frame.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 1
Default Value 0

9: Ambient illumination Lux Level Report

Overview

This parameter defines by how much Lux Level must change, in lux, to be reported to the main controller.

Property Value
Configuration ID config_9_2
Data Type INTEGER
Range 0 to 255
Default Value 100

10: Led Flash Enable

This parameter defines the Led on/off enable

Overview

This parameter defines the Led on/off enable. If this parameter is set to ‘1’, the led blink will be enabled, the led will flash once when motion sensor detect a movement. Otherwise, the led will be turned off always.

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 0 to 1
Default Value 1

1: GROUP 1

lifeline service that assigned to Motion detector status

Overview

GROUP 1 is lifeline service that assigned to Sensor (Motion detector) status – Open/Close. It enables the sensor to send reports and readings to Z-Wave Controller or ZWave Gateway whenever the sensor is triggered. This Group Supports:

  • NOTIFICATION_REPORT_V4
  • SENSOR_BINARY_REPORT_V2
  • SENSOR_MULTILEVEL_REPORT_V7
  • BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION
Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: GROUP 2

allows for sending control commands to associated devices

Overview

GROUP 2 allows for sending control commands to associated devices such as relay module, lighting, etc. This association group is configured through the advanced parameters no. 2, 3, 5 and 8. This Group Supports:

  •  BASIC_SET
Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: GROUP 3

allows for Send Notification to associated devices

Overview

GROUP 3 allows for Send Notification to associated devices in this group. This Group Supports:

  • NOTIFICATION_REPORT_V4
Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: GROUP 4

allows for Send Sensor Binary Report to associated devices

Overview

ROUP 4 allows for Send Sensor Binary Report to associated devices in this group. This Group Supports:

  • SENSOR_BINARY_REPORT_V2
Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.