The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZEN20 Smart Energy Power Strip

This describes the Z-Wave device ZEN20, manufactured by Willis Electric Co., Ltd. with the thing type UID of willis_zen20_00_000.

ZEN20 product image

The ZEN20 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

Inclusion Information

  1. Plug the power strip into a grounded receptacle located within direct range from your Z- Wave gateway controller
  2. Put your Z-Wave controller in inclusion mode
  3. Press and release the CH1 power button on the strip 3 times quickly
  4. A new on / off device should appear on your controller’s device list

Troubleshooting Tips

If you are unable to include the Z-Wave power strip to your controller, please try one of the following:

  • Bring the power strip closer to your Z-Wave controller
  • Press and release the CH1 power button quickly 7-8 times once you put the controller in the inclusion mode to ensure the command has gone through
  • Put your controller in the EXCLUSION mode and press and release the CH1 power button quickly 3 times, then try adding it to your network again

Exclusion Information

  1. Plug the power strip into a grounded receptacle located within direct range from your Z-Wave gateway controller
  2. Put your Z-Wave controller in exclusion mode
  3. Press and release the CH1 power button on the strip 3 times quickly
  4. The device should disappear from your controller’s device list

Please repeat the process following all steps carefully if the first attempt is unsuccessful

Channels

The following table summarises the channels available for the ZEN20 -:

Channel Channel Id Category Item Type
Switch 1 switch_binary1 Switch Switch
Switch 2 switch_binary2 Switch Switch
Switch 3 switch_binary3 Switch Switch
Switch 4 switch_binary4 Switch Switch
Switch 5 switch_binary5 Switch Switch

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Switch 3

Switch the power on and off.

The switch_binary3 channel supports the Switch item and is in the Switch category.

Switch 4

Switch the power on and off.

The switch_binary4 channel supports the Switch item and is in the Switch category.

Switch 5

Switch the power on and off.

The switch_binary5 channel supports the Switch item and is in the Switch category.

Device Configuration

The device has no configuration parameters configured.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 3

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 4

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 5

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.