The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZEN22 Z-Wave Plus Dimmer Light Switch

This describes the Z-Wave device ZEN22, manufactured by Zooz with the thing type UID of zooz_zen22_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

ZEN22 product image

The ZEN22 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

  • Manual or remote on/off and dimming control from your mobile device or computer (when included to a Z-Wave gateway controller)
  • Universal 3-way capability – works with existing 3-way switches as long as neutral is present
  • Z-Wave Plus with improved 500 chip for faster and safer wireless communication
  • Works with LED, CFL, and incandescent bulbs
  • Remembers and restores on/off / brightness status after power failure
  • Based on universal multilevel switch command class - supported by most Z-Wave controllers
  • May be associated and grouped with other Z-Wave devices for advanced home automation
  • Customizeable LED indicator
  • Air-gap switch for added safety
  • Modern paddle design
  • Built-in Z-Wave signal repeater for a stronger, more reliable network

Inclusion Information

1. Bring your Z-Wave gateway hub or controller as close to the switch as possible

2. Put your Z-Wave controller into inclusion mode

3. Tap the upper paddle of the switch 3 times very quickly to finalize the inclusion process

4. A new dimming device will appear on your controller’s device list

Exclusion Information

1. Bring your Z-Wave gateway hub or controller as close to the switch as possible

2. Put your Z-Wave controller into exclusion mode

3. Tap the lower paddle of the switch 3 times very quickly to finalize the exclusion process

4. The device will disappear from your controller’s device list

Channels

The following table summarises the channels available for the ZEN22 -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 3 configuration parameters available in the ZEN22. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Paddle Control Choose Paddle Functionality
2 LED Indicator Control Choose LED Functionality
3 Enable / Disable LED Indicator Enable or disable the LED indicator
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Paddle Control

Choose Paddle Functionality

The following option values may be configured -:

Value Description
0 Upper paddle turns light on, lower paddle turns light off
1 Upper paddle turns light off, lower paddle turns light on

The manufacturer defined default value is 1 (Upper paddle turns light off, lower paddle turns light on).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: LED Indicator Control

Choose LED Functionality

The following option values may be configured -:

Value Description
0 LED on when switch off, LED off when switch off
1 LED on when switch on, LED off when switch off

The manufacturer defined default value is 0 (LED on when switch off, LED off when switch off).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Enable / Disable LED Indicator

Enable or disable the LED indicator

The following option values may be configured -:

Value Description
0 LED indicator is enabled
1 LED indicator is disabled

The manufacturer defined default value is 0 (LED indicator is enabled ).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZEN22 supports 1 association group.

Group 1: Lifeline

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.