The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZEN24 Z-Wave Plus Toggle Dimmer Light Switch Ver 2.0

This describes the Z-Wave device ZEN24, manufactured by Zooz with the thing type UID of zooz_zen24_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

ZEN24 product image

The ZEN24 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

  • Manual or remote on/off and dimming control from your mobile device or computer (when included to a Z-Wave gateway controller)
  • Universal 3-way capability – works with existing 3-way switches as long as neutral is present
  • Z-Wave Plus with improved 500 chip for faster and safer wireless communication
  • Works with LED, CFL, and incandescent bulbs
  • Remembers and restores on/off / brightness status after power failure
  • Based on universal multilevel switch command class - supported by most Z-Wave controllers
  • May be associated and grouped with other Z-Wave devices for advanced home automation
  • Air-gap switch for added safety
  • Classic toggle design
  • Built-in Z-Wave signal repeater for a stronger, more reliable network

Inclusion Information

1. Bring your Z-Wave gateway hub or controller as close to the switch as possible

2. Put your Z-Wave controller into inclusion mode

3. Toggle the switch UP 3 times very quickly to finalize the inclusion process

4. A new dimming device will appear on your controller’s device list

TROUBLESHOOTING TIPS:

If you are unable to include the Z-Wave switch to your controller, please try one of the following:

  • Bring the controller closer to your ZWave switch or use a hand-held secondary controller for inclusion
  • Toggle your Z-Wave switch UP even quicker at least 5 or 7 times once you put the controller into inclusion mode to ensure the command has gone through
  • Put your controller into EXCLUSION mode and toggle the switch DOWN 3 times quickly, then try adding it to your network again

Exclusion Information

1. Bring your Z-Wave gateway hub or controller as close to the switch as possible

2. Put your Z-Wave controller into exclusion mode 3. Toggle the switch DOWN

3 times very quickly to complete the exclusion process

4. The device will disappear from your controller’s device list

Please repeat the process following all steps carefully if the first attempt is unsuccessful.

Channels

The following table summarises the channels available for the ZEN24 -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 1 configuration parameters available in the ZEN24. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Toggle Control Controls behavior of the toggle switch
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Toggle Control

Controls behavior of the toggle switch Choose if you want the to turn the light on by clicking the toggle up or down Values:

0 – Toggle up turns the light on, toggle down turns the light off (default);

1 – Toggle up turns the light off, toggle down turns the light on Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZEN24 supports 1 association group.

Group 1: Lifeline

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.