The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZSE33 Smart Chime/Alarm

This describes the Z-Wave device ZSE33, manufactured by Zooz with the thing type UID of zooz_zse33_00_000.

The ZSE33 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

Overview

- Audio and visual notifications triggered by other Z-Wave devices or scheduled in your routine

- Choose from 10 different sounds for chime and siren modes

- Advanced configuration available

- Powerful long-lasting batteries

- Z-Wave Plus with improved 500 chip for faster and safer wireless communication

- Small size and quick installation

Model Number: ZSE33

Z-Wave Signal Frequency: 908.42 MHz

Power: 2 CR123 batteries (included)

Power Consumption: 2W

Operating Temperature: 32 – 104 F

Range: Up to 100 feet line of sight

Installation and Use: Indoor only

Dimensions: 2.7” x 1.2”

Weight: 3 oz

Inclusion Information

Auto Inclusion:

1. Put your Z-Wave controller in inclusion mode

2. Carefully remove the cover from the device

3. Remove the plastic pull-tab from the battery slot – the Chime will automatically enter inclusion mode for 20 seconds

4. A new alarm siren / doorbell device will appear on your controller’s device list

Manual Inclusion:

1. Bring the Smart Chime within direct range of your controller

2. Carefully remove the cover from the device

3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly

4. Put your Z-Wave controller in inclusion mode

5. Press and release the Z-Wave button on the Smart Chime 3 TIMES quickly. The LED indicator

will flash quickly

6. A new alarm siren / doorbell device will appear on your controller’s device list (if it connects as an on/off switch, you may need to change the device type manually. Contact us for instructions).

Exclusion Information

1. Make sure the Smart Chime is powered on and located within direct range of your Z-Wave gateway controller

2. Put your Z-Wave controller in exclusion mode

3. Press and release the Z-Wave button 3 TIMES quickly. The LED indicator will flash quickly

4. The Smart Chime should disappear from your controller’s device list

If the first attempt is unsuccessful, please repeat the process following all steps carefully.

Channels

The following table summarises the channels available for the ZSE33 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Alarm alarm_general Door Switch
Battery Level battery-level Battery Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Alarm

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 9 configuration parameters available in the ZSE33. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Siren Volume 3 volume levels for the alarm siren sound.
2 Siren Alarm Duration 5 modes to set the duration for siren alarm
3 Chime Sound Duration how many times the chime should repeat the doorbell sound once triggered by a BASIC_SET alarm command from a door sensor.
4 Chime Volume 3 volume levels for the doorbell sound. Set volume to low, medium, or high.
5   10 different tones for alarm siren
6 Chime Tone 10 different tones for doorbell
7 Siren Alarm or Chime Mode Switch between Siren Alarm (configu-red by parameters 1, 2, 5, 8) and Chime / Doorbell (parameters 3, 4, 6, 9) modes.
8 LED Notifications for Siren Alarm Enable or disable visual alarm for Siren mode. The LED will blink when triggered.
9 LED Notifications for Chime Enable or disable visual alarm for Chime mode. The LED will blink when triggered.

Parameter 1: Siren Volume

3 volume levels for the alarm siren sound. Values: 1 – low, 2 – medium, 3 – high (default) Values in the range 1 to 3 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Siren Alarm Duration

5 modes to set the duration for siren alarm 0 – alarm is off

1 – alarm goes off for 30 seconds

2 – alarm goes off for 60 seconds

3 – alarm goes off for 5 minutes

255 – alarm continues until battery drains

Values: 0, 1 – 3, 255; 1 – default setting. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Chime Sound Duration

how many times the chime should repeat the doorbell sound once triggered by a BASIC_SET alarm command from a door sensor. Values: 0 – chime is off, 1 – 254 (cycles); 255 – chime

sound continues until battery drains; 2 – default setting. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 2.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Chime Volume

3 volume levels for the doorbell sound. Set volume to low, medium, or high. Values: 1 – low, 2 – medium, 3 – high (default) Values in the range 1 to 3 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5:

10 different tones for alarm siren Values: 1-10; 10 – default setting. Values in the range 1 to 10 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: Chime Tone

10 different tones for doorbell Values: 1-10; 4 – default setting. Values in the range 1 to 10 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Parameter 7: Siren Alarm or Chime Mode

Switch between Siren Alarm (configu-red by parameters 1, 2, 5, 8) and Chime / Doorbell (parameters 3, 4, 6, 9) modes. Values: 1 – Siren Alarm enabled; 2 – Chime enabled (default). Values in the range 1 to 2 may be set.

The manufacturer defined default value is 2.

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: LED Notifications for Siren Alarm

Enable or disable visual alarm for Siren mode. The LED will blink when triggered. Values: 0 – LED disabled; 1 – LED enabled (default). Values in the range 0 to 1 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: LED Notifications for Chime

Enable or disable visual alarm for Chime mode. The LED will blink when triggered. Values: 0 – LED disabled (default); 1 – LED enabled. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V8  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  
COMMAND_CLASS_INDICATOR_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.