ZEN06 Smart Plug with 2 USB ports
This describes the Z-Wave device ZEN06, manufactured by Zooz with the thing type UID of zooz_zen06_00_000.
Smart Plug with 2 USB ports
Overview
Product features:
- Manual and remote on / off control
- Energy monitoring
- Scene inclusion for custom automation scenarios when included to a Z-Wave gateway controller
- LED indicator displaying Z-Wave signal strength and power usage
- Security enabled Z-Wave device with AES signal encryption (requires a security enabled gateway controller for full functionality)
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Built-in range extender for a stronger, more reliable network
- 2 USB charging ports for your smart phone or tablet (no Z-Wave functionality)
- Built-in overload protection in Z-Wave outlet and USB ports
How to read LED indicator colors?
- Burgundy = Smart Plug is off
- Blue = 0 – 300 W
- Cyan = 300 – 600 W
- Green = 600 – 900 W
- Yellow = 900 – 1200 W
- Red = 1200 – 1500 W
- Purple = 1500 – 1800 W
- Purple blink = over 1800 W
How to test Z-Wave network range for my Smart Plug?
You can easily check if the Smart Plug is within your Z-Wave controller’s range.
Here is how:
Press and hold the Z-Wave button for 6 to 9 seconds until the LED indicator turns violet.
The LED indicator will then report signal strength.
- Flashing green = direct communication with the primary controller is established and still being diagnosed
- Solid green for 2 seconds = direct communication with the primary controller is stable
- Flashing orange = direct communication with the primary controller is intermittent and being diagnosed
- Solid orange = communication quality is fair
- Solid red = communication with the primary controller has failed
- Press and release the Z-Wave button to exit testing mode.
NOTE: This function may only be activated once the Smart Plug has been included to a ZWave network.
Channels
The following table summarises the channels available for the ZEN06 Smart Plug with 2 USB ports.
| Channel | Channel Id | Channel Type UID | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number | |
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (amps) | meter_current | meter_current | Energy | Number |
| Reset Meter | meter_reset | meter_reset | Energy | Switch |
Device Configuration
The following table provides a summary of the configuration parameters available in the ZEN06 Smart Plug with 2 USB ports. Detailed information on each parameter can be found below.
| Parameter | Description |
|---|---|
| 20: Overload Protection | turns relay off once voltage exceeds 16.5A for over 5 secs if enabled |
| 21: On/Off Status Recovery After Power Failure | Recovery state for power failure |
| 24: On/Off Status Change Notifications | Send notifications to associated devices |
| 27: LED Indicator Control | LED Indicator Control |
| 151: Power Report Value Threshold | Minimum change in watts to report |
| 152: Power Report Percentage Threshold | Minimum percentage change to report |
| 171: Power Report Frequency | How often to report power consumption (W) in secs |
| 172: Energy Report Frequency | How often to report energy usage (KWH) in secs |
| 173: Voltage Report Frequency | How often to report voltage (V) in secs |
| 174: Electricity Report Frequency | How often to report electrical current (A) in secs |
| 1: Lifeline |
20: Overload Protection
turns relay off once voltage exceeds 16.5A for over 5 secs if enabled
Overview
We DO NOT recommend changing this parameter’s value as it may result in device damage and malfunction.
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_20_1 | |||
| Data Type | INTEGER | Default Value | 1 | |
| Options | Disabled (0) | |||
| Enabled (1) |
21: On/Off Status Recovery After Power Failure
Recovery state for power failure
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_21_1 | |||
| Data Type | INTEGER | Default Value | 0 | |
| Options | Previous setting (0) | |||
| ON (1) | ||||
| OFF (2) |
24: On/Off Status Change Notifications
Send notifications to associated devices
Overview
Your Smart Plug will automatically send a notification to the controller and other associated devices if its status changes from on to off or the other way round. Choose when you want it to send the report.
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_24_1 | |||
| Data Type | INTEGER | Default Value | 1 | |
| Options | Disabled (0) | |||
| Send any change (1) | ||||
| Send manual changes (2) |
27: LED Indicator Control
LED Indicator Control
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_27_1 | |||
| Data Type | INTEGER | Default Value | 0 | |
| Options | Display power consumption always (0) | |||
| Display power consumption at state change (1) |
151: Power Report Value Threshold
Minimum change in watts to report
Overview
Choose how you want your Smart Plug to report power consumption to your controller and associated devices.
The number entered as value corresponds to the number of Watts the appliance needs to go over for the change to be reported.
So if 50 Watts are entered by default, the smart plug will report any change in power usage over 50 Watts (whether it’s at least 50 Watts more or 50 Watts less compared to previous report).
Values: 0 – 65535;
0 – disabled (it will not report power consumption based on value change);
| Property | Value |
|---|---|
| Configuration ID | config_151_2 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 50 |
152: Power Report Percentage Threshold
Minimum percentage change to report
Overview
Choose how you want your Smart Plug to report power consumption to your controller and associated devices by percentage rate.
The number entered as value corresponds to the percentage in power usage change the appliance needs to go over for the event to be reported.
So if 10% is entered by default, the Smart Plug will report any change in power consumption over 10% (whether it’s at least 10% more or 10% less power consumption compared to previous report).
Values: 0 – 255;
0 – disabled (it will not report power consumption based on percentage change);
| Property | Value |
|---|---|
| Configuration ID | config_152_1 |
| Data Type | INTEGER |
| Range | 0 to 255 |
| Default Value | 10 |
171: Power Report Frequency
How often to report power consumption (W) in secs
Overview
Choose how often you want your Smart Plug to report power consumption (W) to your controller and associated device.
The number entered as value corresponds to the number of seconds.
So if 30 is entered by default, the Smart Plug will report power consumption every 30 seconds.
Values: 5 – 2678400;
0 – disabled (it will not report power consumption);
| Property | Value |
|---|---|
| Configuration ID | config_171_4 |
| Data Type | INTEGER |
| Range | 0 to 2678400 |
| Default Value | 30 |
172: Energy Report Frequency
How often to report energy usage (KWH) in secs
Overview
Choose how often you want your Smart Plug to report energy usage (KWH) to your controller and associated device.
The number entered as value corresponds to the number of seconds.
So if 300 is entered by default, the smart plug will report energy usage every 300 seconds (5 minutes).
Values: 5 – 2678400;
0 – disabled (it will not report energy usage);
| Property | Value |
|---|---|
| Configuration ID | config_172_4 |
| Data Type | INTEGER |
| Range | 0 to 2678400 |
| Default Value | 300 |
173: Voltage Report Frequency
How often to report voltage (V) in secs
Overview
Choose how often you want your Smart Plug to report voltage (V) to your controller and associated device.
The number entered as value corresponds to the number of seconds.
Values: 5 – 2678400;
0 – disabled
| Property | Value |
|---|---|
| Configuration ID | config_173_4 |
| Data Type | INTEGER |
| Range | 0 to 2678400 |
| Default Value | 0 |
174: Electricity Report Frequency
How often to report electrical current (A) in secs
Overview
Choose how often you want your Smart Plug to report levels of electrical current (A) to your controller and associated device.
The number entered as value corresponds to the number of seconds.
Values: 5 – 2678400;
0 – disabled
| Property | Value |
|---|---|
| Configuration ID | config_174_4 |
| Data Type | INTEGER |
| Range | 0 to 2678400 |
| Default Value | 0 |
1: Lifeline
| Property | Value |
|---|---|
| Configuration ID | group_1 |
| Data Type | TEXT |
| Range | to |
Did you spot an error in the above definition or want to improve the content? You can edit the database here.