ZSE09 Motion and Light Mini Sensor

This describes the Z-Wave device ZSE09, manufactured by Zooz with the thing type UID of zooz_zse09_00_000.

Motion and Light Mini Sensor

Channels

The following table summarises the channels available for the ZSE09 Motion and Light Mini Sensor.

Channel Channel Id Channel Type UID Category Item Type
sensor_binary sensor_binary sensor_binary Door Switch
sensor_binary sensor_binary sensor_binary Door Switch
alarm_motion alarm_motion alarm_motion Door Switch
sensor_luminance sensor_luminance sensor_luminance Temperature Number
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the ZSE09 Motion and Light Mini Sensor. Detailed information on each parameter can be found below.

Parameter Description
1: Motion Sensitivity 8 = high; 255 = low
2: Trigger ON Duration delay after motion before turning OFF
3: Trigger Action Brightness to turn on the associated device 1-99, 255=ON
4: Motion Detection 255=Motion Detection Enabled
5: Light Trigger Level Max Light level which enables motion trigger
6: Motion Trigger Interval Minimum time between motion triggers.
7: Light Polling Interval Interval between light level reporting
8: Light Trigger 255=enable Light sensor
9: Light Report Light level change to be reported.
10: LED Notifications 0=disable, 1=enable
1: Status to controller  
2: BASIC BASIC_SET Trigger associated devices
3: Notification Reports NOTIFICATION_REPORT_V4
4: SENSOR BINARY SENSOR_BINARY_REPORT_V2

1: Motion Sensitivity

8 = high; 255 = low

Overview

Adjust detection by choosing a value from 8 to 255, where 8 stands for high sensitivity level (detection of the smallest movement) and 255 stands for very low sensitivity level

Property Value
Configuration ID config_1_1
Data Type INTEGER
Range 8 to 255
Default Value 12

2: Trigger ON Duration

delay after motion before turning OFF

Overview

Set the duration (in seconds) you want the associated device to stay ON for after being triggered by the sensor before it automatically turns OFF. Must be greater than value set in parameter 6.

Property Value
Configuration ID config_2_2
Data Type INTEGER
Range 5 to 600
Default Value 30

3: Trigger Action

Brightness to turn on the associated device 1-99, 255=ON

Overview

You can choose if your Mini Sensor turns an associated device on or off when sending the BASIC SET command. Use value 0 to turn the associated device OFF and value 255 to turn it ON. Adjust brightness level for a Z-Wave dimmer (Multilevel switch) by putting in any value between 1 and 99. 

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 255
Default Value 255

4: Motion Detection

255=Motion Detection Enabled

Property Value
Configuration ID config_4_1
Data Type INTEGER
Range 0 to 255
Default Value 255

5: Light Trigger Level

Max Light level which enables motion trigger

Overview

Set your light sensor as a secondary trigger for associated devices. If light level in a room falls beyond the set point and motion is detected, the Mini Sensor will send BASIC_SET command to associated devices to turn ON. The number entered as the value corresponds to the number of LUX. By default, if motion has been detected by your Mini Sensor, the associated device will turn ON if light level last reported by the sensor is under 100 LUX. 

Property Value
Configuration ID config_5_2
Data Type INTEGER
Range 0 to 1000
Default Value 100

6: Motion Trigger Interval

Minimum time between motion triggers.

Overview

Adjust the time (in seconds) when motion is reported again after initial trigger. By default, with continued motion, the Mini Sensor will report motion again 8 seconds after it’s last detection. The value set for this parameter can NOT be greater than value set in parameter 2. NOTE: Small interval will increase activity and decrease battery life.

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 1 to 8
Default Value 8

7: Light Polling Interval

Interval between light level reporting

Overview

Decide how often (in seconds) you want the Mini Sensor to report light level to the controller and associated devices. By default, the Mini Sensor will report light level values every 3 minutes. The value set for this parameter can NOT be greater than the wake-up interval. NOTE: Small interval will increase activity and decrease battery life.

Property Value
Configuration ID config_7_2
Data Type INTEGER
Range 60 to 36000
Default Value 180

8: Light Trigger

255=enable Light sensor

Overview

Use this parameter to enable and disable the light sensor as secondary trigger. If this feature is enabled, the Mini Sensor will activate associated devices based on motion AND light level set in parameter 5

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 255
Default Value 0

9: Light Report

Light level change to be reported.

Overview

Choose light level (in LUX) change to be reported by the Mini Sensor to the controller. By default, the sensor will report any change of 100 LUX or more.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 255
Default Value 255

10: LED Notifications

0=disable, 1=enable

Overview

Use this parameter to turn LED notifications on or off for motion detection.

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 0 to 1
Default Value 1

1: Status to controller

Overview

lifeline communication of motion / no motion and light level status to Z-Wave controller. Supported command classes: NOTIFICATION_REPORT_V4 SENSOR_BINARY_REPORT_V2 SENSOR_MULTILEVEL_REPORT_V7 BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: BASIC

BASIC_SET Trigger associated devices

Overview

control command communication to associated Z-Wave devices in the network. Use parameters 2, 3, 5, and 8 to configure this group’s settings. Supported command classes: BASIC_SET 

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Notification Reports

NOTIFICATION_REPORT_V4

Overview

notifications to Z-Wave devices associated in this group. Supported command classes: NOTIFICATION_REPORT_V4

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: SENSOR BINARY

SENSOR_BINARY_REPORT_V2

Overview

notifications to Z-Wave devices associated in this group. Supported command classes: SENSOR_BINARY_REPORT_V2

Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.