ZSE33 Smart Chime/Alarm

This describes the Z-Wave device ZSE33, manufactured by Zooz with the thing type UID of zooz_zse33_00_000.

Smart Chime/Alarm

Overview

- Audio and visual notifications triggered by other Z-Wave devices or scheduled in your routine

- Choose from 10 different sounds for chime and siren modes

- Advanced configuration available

- Powerful long-lasting batteries

- Z-Wave Plus with improved 500 chip for faster and safer wireless communication

- Small size and quick installation

Model Number: ZSE33

Z-Wave Signal Frequency: 908.42 MHz

Power: 2 CR123 batteries (included)

Power Consumption: 2W

Operating Temperature: 32 – 104 F

Range: Up to 100 feet line of sight

Installation and Use: Indoor only

Dimensions: 2.7” x 1.2”

Weight: 3 oz

Inclusion Information

Auto Inclusion:

  1. Put your Z-Wave controller in inclusion mode

  2. Carefully remove the cover from the device

  3. Remove the plastic pull-tab from the battery slot – the Chime will automatically enter inclusion mode for 20 seconds

  4. A new alarm siren / doorbell device will appear on your controller’s device list

Manual Inclusion:

  1. Bring the Smart Chime within direct range of your controller

  2. Carefully remove the cover from the device

  3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly

  4. Put your Z-Wave controller in inclusion mode

  5. Press and release the Z-Wave button on the Smart Chime 3 TIMES quickly. The LED indicator

will flash quickly

  1. A new alarm siren / doorbell device will appear on your controller’s device list (if it connects as an on/off switch, you may need to change the device type manually. Contact us for instructions).

Exclusion Information

  1. Make sure the Smart Chime is powered on and located within direct range of your Z-Wave gateway controller

  2. Put your Z-Wave controller in exclusion mode

  3. Press and release the Z-Wave button 3 TIMES quickly. The LED indicator will flash quickly

  4. The Smart Chime should disappear from your controller’s device list

If the first attempt is unsuccessful, please repeat the process following all steps carefully.

Channels

The following table summarises the channels available for the ZSE33 Smart Chime/Alarm.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Alarm alarm_general alarm_general Door Switch
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the ZSE33 Smart Chime/Alarm. Detailed information on each parameter can be found below.

Parameter Description
1: Siren Volume 3 volume levels for the alarm siren sound.
2: Siren Alarm Duration 5 modes to set the duration for siren alarm
3: Chime Sound Duration how many times the chime should repeat the doorbell sound once triggered by a BASIC_SET a…
4: Chime Volume 3 volume levels for the doorbell sound. Set volume to low, medium, or high.
5: 10 different tones for alarm siren
6: Chime Tone 10 different tones for doorbell
7: Siren Alarm or Chime Mode Switch between Siren Alarm (configu-red by parameters 1, 2, 5, 8) and Chime / Doorbell (pa…
8: LED Notifications for Siren Alarm Enable or disable visual alarm for Siren mode. The LED will blink when triggered.
9: LED Notifications for Chime Enable or disable visual alarm for Chime mode. The LED will blink when triggered.

1: Siren Volume

3 volume levels for the alarm siren sound.

Overview

Values: 1 – low, 2 – medium, 3 – high (default)

Property Value
Configuration ID config_1_1
Data Type INTEGER
Range 1 to 3
Default Value 3

2: Siren Alarm Duration

5 modes to set the duration for siren alarm

Overview

0 – alarm is off

1 – alarm goes off for 30 seconds

2 – alarm goes off for 60 seconds

3 – alarm goes off for 5 minutes

255 – alarm continues until battery drains

Values: 0, 1 – 3, 255; 1 – default setting.

Property Value
Configuration ID config_2_1
Data Type INTEGER
Range 0 to 255
Default Value 1

3: Chime Sound Duration

how many times the chime should repeat the doorbell sound once triggered by a BASIC_SET alarm command from a door sensor.

Overview

Values: 0 – chime is off, 1 – 254 (cycles); 255 – chime

sound continues until battery drains; 2 – default setting.

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 255
Default Value 2

4: Chime Volume

3 volume levels for the doorbell sound. Set volume to low, medium, or high.

Overview

Values: 1 – low, 2 – medium, 3 – high (default)

Property Value
Configuration ID config_4_1
Data Type INTEGER
Range 1 to 3
Default Value 3

5:

10 different tones for alarm siren

Overview

Values: 1-10; 10 – default setting.

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 1 to 10
Default Value 10

6: Chime Tone

10 different tones for doorbell

Overview

Values: 1-10; 4 – default setting.

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 1 to 10
Default Value 4

7: Siren Alarm or Chime Mode

Switch between Siren Alarm (configu-red by parameters 1, 2, 5, 8) and Chime / Doorbell (parameters 3, 4, 6, 9) modes.

Overview

Values: 1 – Siren Alarm enabled; 2 – Chime enabled (default).

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 2
Default Value 2

8: LED Notifications for Siren Alarm

Enable or disable visual alarm for Siren mode. The LED will blink when triggered.

Overview

Values: 0 – LED disabled; 1 – LED enabled (default).

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 1
Default Value 1

9: LED Notifications for Chime

Enable or disable visual alarm for Chime mode. The LED will blink when triggered.

Overview

Values: 0 – LED disabled (default); 1 – LED enabled.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 1
Default Value 1

Did you spot an error in the above definition or want to improve the content? You can edit the database here.