ZME_KFOB-S Secure 4 Button Key Chain Controller

This describes the Z-Wave device ZME_KFOB-S, manufactured by Z-Wave.Me with the thing type UID of zwaveme_zmekfobs_00_000.

Secure 4 Button Key Chain Controller

Channels

The following table summarises the channels available for the ZME_KFOB-S Secure 4 Button Key Chain Controller.

Channel Channel Id Channel Type UID Category Item Type
Scene Number scene_number scene_number   Number
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the ZME_KFOB-S Secure 4 Button Key Chain Controller. Detailed information on each parameter can be found below.

Parameter Description
1: Button 1 and 3 pair mode Set Button 1 and 3 pair mode
2: Button 2 and 4 pair mode Set Button 2 and 4 pair mode
11: Command to Control Group A Set Command to Control Group A
12: Command to Control Group B Set Command to Control Group B
13: Command to Control Group C Set Command to Control Group C
14: Command to Control Group D Set Command to Control Group D
21: Send the following Switch All commands Set Send the following Switch All commands
22: Invert buttons Invert buttons
25: Blocks wakeup even when wakeup interval is set Set Blocks wakeup even when wakeup interval is set
30: Send unsolicited Battery Report on Wake Up Set Send unsolicited Battery Report on Wake Up
1: Lifeline  
2: Control Group A  
3: Control Group B  
4: Control Group C  
5: Control Group D  

1: Button 1 and 3 pair mode

Set Button 1 and 3 pair mode

Overview

In separate mode button 1 works with group A, button 3 with groups C. Click is On, Hold is dimming Up, Double click is Off, Click-Hold is dimming Down. In pair button 1/3 are Up/Down correspondingly. Click is On/Off, Hold is dimming Up/Down. Single clicks works with group A, double click with group C. Default Value: 01

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 1
Options Separately (0)      
  In pair without double clicks (1)      
  In pair with double clicks (2)      

2: Button 2 and 4 pair mode

Set Button 2 and 4 pair mode

Overview

In separate mode button 2 works with control group B, button 4 with control group D. Click is On, Hold is dimming Up, Double click is Off, Click-Hold is dimming Down. In pair button B/D are Up/Down correspondingly. Click is On/Off, Hold is dimming Up/Down. Single clicks works with group B, double click with group D. Default Value: 01

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 1
Options Separately (0)      
  In pair without double clicks (1)      
  In pair with double clicks (2)      

11: Command to Control Group A

Set Command to Control Group A

Overview

This parameter defines the command to be sent to devices of control group A when the related button is pressed. Default Value: 08

Property Value      
Configuration ID config_11_1      
Data Type INTEGER   Default Value 8
Options Disabled (0)      
  Switch On/Off and Dim (send Basic Set and Switch Multilevel) (1)      
  Switch On/Off only (send Basic Set) (2)      
  Switch All (3)      
  Send Scenes (4)      
  Send Preconfigured Scenes (5)      
  Control devices in proximity (6)      
  Control DoorLock (7)      
  Central Scene to Gateway (8)      

12: Command to Control Group B

Set Command to Control Group B

Overview

This parameter defines the command to be sent to devices of control group B when the related button is pressed. Default Value: 08

Property Value      
Configuration ID config_12_1      
Data Type INTEGER   Default Value 8
Options Disabled (0)      
  Switch On/Off and Dim (send Basic Set and Switch Multilevel) (1)      
  Switch On/Off only (send Basic Set) (2)      
  Switch All (3)      
  Send Scenes (4)      
  Send Preconfigured Scenes (5)      
  Control devices in proximity (6)      
  Control DoorLock (7)      
  Central Scene to Gateway (8)      

13: Command to Control Group C

Set Command to Control Group C

Overview

This parameter defines the command to be sent to devices of control group C when the related button is pressed. Default Value: 08

Property Value      
Configuration ID config_13_1      
Data Type INTEGER   Default Value 8
Options Disabled (0)      
  Switch On/Off and Dim (send Basic Set and Switch Multilevel) (1)      
  Switch On/Off only (send Basic Set) (2)      
  Switch All (3)      
  Send Scenes (4)      
  Send Preconfigured Scenes (5)      
  Control devices in proximity (6)      
  Control DoorLock (7)      
  Central Scene to Gateway (8)      

14: Command to Control Group D

Set Command to Control Group D

Overview

This parameter defines the command to be sent to devices of control group D when the related button is pressed. Default Value: 08

Property Value      
Configuration ID config_14_1      
Data Type INTEGER   Default Value 8
Options Disabled (0)      
  Switch On/Off and Dim (send Basic Set and Switch Multilevel) (1)      
  Switch On/Off only (send Basic Set) (2)      
  Switch All (3)      
  Send Scenes (4)      
  Send Preconfigured Scenes (5)      
  Control devices in proximity (6)      
  Control DoorLock (7)      
  Central Scene to Gateway (8)      

21: Send the following Switch All commands

Set Send the following Switch All commands

Overview

Send the following Switch All commands

Property Value      
Configuration ID config_21_1      
Data Type INTEGER   Default Value 1
Options Switch off only (1)      
  Switch on only (2)      
  Switch all on and off (255)      

22: Invert buttons

Invert buttons

Overview

Invert buttons

Property Value      
Configuration ID config_22_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

25: Blocks wakeup even when wakeup interval is set

Set Blocks wakeup even when wakeup interval is set

Overview

If the KFOB wakes up and there is no controller nearby, several unsuccessful communication attempts will drain battery
Size: 1 Byte, Default Value: 00

Property Value      
Configuration ID config_25_1      
Data Type INTEGER   Default Value 0
Options Wakeup is blocked (0)      
  Wakeup is possible if configured accordingly (1)      

30: Send unsolicited Battery Report on Wake Up

Set Send unsolicited Battery Report on Wake Up

Overview

Set Send unsolicited Battery Report on Wake Up

Property Value      
Configuration ID config_30_1      
Data Type INTEGER   Default Value 1
Options No (0)      
  To same node as wake up notification (1)      
  Broadcast to neighbors (2)      

1: Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Control Group A

Overview

Control Group A, controlled by button 1 or single clicks of buttons

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Control Group B

Overview

Control Group B, controlled by button 2 or single clicks of buttons 2

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Control Group C

Overview

Control Group C, controlled by button 3 or double clicks of buttons 1

Property Value
Configuration ID group_4
Data Type TEXT
Range to

5: Control Group D

Overview

Control Group D, controlled by button 4 or double clicks of buttons 2

Property Value
Configuration ID group_5
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.