Vitotronic Binding

Viessmann heating systems with Vitotronic has a optolink Interface for maintenance. This interface can use for get/set data in the heating system. see on openv

The Vitotronic binding is a solution to bind this interface into openHAB2. It supports the separation of the heating adaption from the integration in openHAB2.


The adapter transform the address oriented raw interface of the Vitotronic to a abstract format. The adapter itself is not a part of the openhab2 binding.
A alpha version is available here
More Information about the adapter

Supported Things

For easy using are the main things of a heating system are already define in this binding:

  • heating (Vitotronic core system)
  • pelletburner (Pellet Fireplace, works for wood also)
  • oilburner (Oil Fireplace)
  • storagetank (Storage Tank, stores heat in a water tank on 3 levels: bottom, middle, top=hot water)
  • circuit (Heating circuit controls the flow between the heating system and the radiators in the rooms)
  • solar (Solar water heating (SWH): Convert sunlight into energy for water heating)

For advanced used 3 basic things of a headingsystem define also.

  • temperaturesensor (Single temperature sensor)
  • pump (Single pump)
  • valve (Single valve)

Note: The mapping of things and channels to the heating system addresses must be done in the adapter.


The binding discovers the adapter with broadcast and put the found vitotronic:bridge into the inbox. For automatic detection the adapter and openHAB must be on the same LAN. The discovery itself must be start in the Paper-UI.
If the bridge isn’t on the same LAN the bridge can also add manually. In this case the IP-Address and the adapterID is required. Íf the vitotronic:bridge added a second discovery will be start. It discovers all things, define in the adapter and put found things into the inbox.

Binding Configuration

Binding itself has 4 configuration parameters:

  • ipAddress (The IP address of the Optolink adapter)
  • port (Port of the LAN gateway. Default: 31113)
  • adapterID (The ID/Name of the adapter)
  • refreshInterval (Refresh time for data in seconds. Default: 600 seconds)

If the adapter is automatic discovered the ipAddress, and adapterID will be set by discovery.
The rereshInterval can be set between 60 and 600 seconds. The minimal setting is dependent of the performance of the adapter.

Thing Configuration

There is no configuration of Things necessary. Only some channels are set active by default. If this channels are defined in the adapter and will be used in openHAB it must set active manually.
Don’t change the Thing Name. It is the reference to the name in the adapter.


The follow channels are implemented:

Channel Type ID Item Type Description
systemtime DateTime DateTime of the heating system
outside_temp Number Outside temperature sensor
boiler_temp Number Temperature sensor of boiler (fireplace)
flowuprating Switch Pump state of flow up rating
flame_temp Number Temperature of flame
airshutter_prim Number Position of the primary air shutter
airshutter_sec Number Position of the secondary air shutter
lambdasensor Number Oxygen content of the exhaust air
fanspeed Number Fan Speed in rpm
fanspeed_target Number Fan Speed in rpm
error Switch  
starts Number Count of starts
ontime Number Ontime in hours
consumedpellets Number Consumed Pellets since start of heating in tons
power Number Power of the pellet burner
powerlevel Number Power of the oil burner
actualpower Number Actual power of the burner
ontimelevel1 Number Ontime in hours
ontimelevel2 Number Ontime in hours
consumedoil Number Consumed Oil since start of heating in Liter
hotwater_temp Number Temperature sensor of the hot water
middle_temp Number Temperature sensor in the middle of the storage tank
bottom_temp Number Temperature sensor at the bottom of the storage tank
circuitpump Switch Circuit pump state
flowtemperature Number Temperature sensor of the ciruit flow
pump Switch Pump state
operationmode Number Operationmode
savemode Switch Savemode on/off
partymode Switch Partymode on/off
party_temp Number Target temperature of party mode
room_temp Number Target temperature of rooms
save_temp Number Target temperature of save mode
gradient Number The gradient relativ to outside temperature
niveau Number The niveau relativ to outside temperature
collector_temp Number Actual temperature of the collector
storagetank_temp Number Actual temperature of the storage tank (solar sensor)
bufferload Switch State of the pump (on/off)
loadsuppression Switch State of the load suppression (on/off)
producedheat Number Produced heat since starting solar system
temperature Number Generic temperature sensor
valve Number Value of a generic valve

Full Example